Tag: 26650 Flashlight

Posted on

Thrunite – TC20 Pro Review (3294 Lumens, 350 meters throw, USB-C, 20%)

Today I am looking at the Thrunite TC20 Pro. This is an updated version of the TC20 V2 that I looked at in the past, and the main difference is that the Pro is using a Cree XHP 70 HI LED and smooth reflector. As a part of this review, I will be comparing it to the Fenix PD36R Pro during my night shots section later on. Thanks to Thrunite for sending this to me to look at and offer an unbias review. Any discounts or deals I have for the TC20 Pro will be in the description below along with links to my social media accounts that I encourage you to go and follow. 

 

Watch this review on YouTube: 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on TikTok: https://www.tiktok.com/@liquidretro1

Enjoy this review? Buy me a Coffee/Beer: https://www.buymeacoffee.com/Liquidretro

Find all my social media at https://linktr.ee/liquidretro

See my Amazon Store with my gear recommendations https://www.amazon.com/shop/liquidretro

 

Get the Thrunite TC20 Pro at https://amzn.to/3mU8U6g amd save 20% using code 47C8HFMW through midnight PDT 3/26/23

 

Packaging & Accessories

Standard Thrunite brown cardboard box here with the elastic band, I would call it functional minimalism. Inside is the entire kit with almost everything you need to maintain and use the light for years. You get the light itself, a 5000mAh 26650 Thrunite battery, nylon holster, USB-A to C charging cable, lanyard, a bag of extras including o’rings, button seal, USB port cover, and split ring, a manual, and warranty card.

 

Construction

Visually and construction-wise, the TC20 Pro is pretty much identical to the TC20 V2, with the main differences being the LED and Lens combination. The light is made from Aluminum and hard anodized black. Build quality is always good from Thrunite and this is no exception. The tail cap provides a flat surface that allows for tail standing and has a lanyard hole. The cap is removable and non-magnetic. Inside there is a stout spring on the tail end only.

The body tube has milled blocks in an almost frag pattern for grip. The corners are well-chamfered though so it’s not too aggressive. Square threads on both ends are anodized, smooth, and nonreversible.

The head features the standard Thrunite electronic switch with a metal button on top, and a small battery indicator LED in the middle. Directly opposite the button is the USB-C charging port that’s covered via a silicone rubber flap. It’s decent fitting and does stay out of the way. The light has moderate milling at the top for heat dissipation and weight reduction. The bezel is flat. The lens is AR coated and the reflector is smooth.

 

UI

UI here is Thrunite’s standard. Single press to turn on, long press once on to cycle up between the 3 main modes, double press to go to Turbo, triple press to go to strobe. It’s a very simple interface, and it’s easy to use which is nice but also limiting. A fast ramping interface would work pretty well here too given the limited number of modes and wide range of outputs it must cover. 

 

Retention

Retention options include the included nylon holster. It has elastic sides, plastic dring, and a fixed belt loop. It gets the job done but is just of average quality. The light also comes with a branded lanyard and split ring that can be attached to the tail if you wish.

 

Size & Weight

I measured the length at 118.1mm, the diameter of the body tube at 32.6mm, diameter of the head at 42mm. The weight of the TC20 Pro with the battery is 242.5g. The light is IP68 water-rated to 2 meters. Here are some comparisons with other flashlights, including the Fenix PD36R Pro I will be comparing it to in the night shots coming up soon.

LED & Beam

The TC20 Pro is using a Cree XHP 70 HI LED in cool white. On my Opple meter measured the tint at 6092k and 69 CRI. DUV is fairly neutral with no major tint shifts. When I compare it to my TC20 V2, it has much less tint shift and much less yellow/green, especially at lower outputs. The beam on the TC20 Pro is more spotty and throws a bit further and that makes sense with the smooth emitter and dedomed LED. When I compare it to the Fexnix PD36R Pro the hot spot is of a similar size but has a smoother transition into the spill where as the Fenix is much more pronounced. I would say the tint of the Fenix is more green, especially at lower outputs. There is a small amount of very fast PWM on all modes of the TC20 Pro.

 

Outputs

Heat & Runtime

The light is able to sustain it’s 3500+ lumens for 3:30 before stepping down to around 1800 lumens where it will run for 32 minutes, before stepping down to about 1600 lumens to finish out the remainder of it’s 1:00:00 runtime. Peak heat during this time was about 59C. Running on medium nets an impressive 9:30:00.

Where this light really shines in my opinion is the amount of time it can sustain well over 1000 lumens. This light maintains over 1400 lumens for 1:40:00. I frequently get asked what light can I buy that will stay over 1000 or 2000 lumens for an hour, well here is a good option for you if that’s what you’re looking for. In comparison to the TC20 V2 the Pro here doesn’t have quite a long of runtime but that’s to be expected with this different LED and more overall output.

 

Recharging

The TC20 Pro has onboard USB-C charging that’s protected by a silicone rubber port cover. I charged the light charged the light from LVP to full at 4.17v in 3:17:00. You are able to use the light during charging but only in low and medium modes. It charges via USB-C to C or PD without an issue. While the included battery is officially rated at 5000mAh, I tested mine with my Vapcell S4 Plus at 5437mAh.  

 

Conclusion

The Thruntie TC20 Pro is a worthwhile upgrade to the V2. It takes what was a moderately floody light and increases its ability to throw, while still maintaining the size and form factor we know. The tint here is better on the Pro, and over it’s competitors in my opinion, and I prefer the beam tint and shape on the Pro. You do take some small decreases in overall runtime though due to that higher comparison. 

Compared to the Fenix PD36R Pro, the TC20 Pro is less tactical with it’s UI and a bit more general purpose in my opinion. It’s also generally a better value and a light I can recommend over either the TC20 V2, or the PD36R Pro dollar for dollar in my opinion. 

 

Get the Thrunite TC20 Pro at https://amzn.to/3mU8U6g amd save 20% using code 47C8HFMW through midnight PDT 3/26/23

Posted on

Thrunite TC20 V2 Review (4000 Lumens, XHP 70.2, USB-C)

Today I am taking at the Thrunite TC20 V2. It’s not the newest model but it’s still recent and an update on the Thrunite TC20 V1. It’s running a Cree XHP70.2 LED, a 26650 battery, and has onboard USB-C charging. If you want a light that can sustain 2000 lumens for more than an hour, listen up. Thanks to Thrunite for “accidentally” sending this to me ?.

 

Watch this review on YouTube: 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on TikTok: https://www.tiktok.com/@liquidretro1

Enjoy this review? Buy me a Coffee/Beer: https://www.buymeacoffee.com/Liquidretro

Find all my social media at https://linktr.ee/liquidretro

See my Amazon Store with my gear recommendations https://www.amazon.com/shop/liquidretro

 

Get the TC20 V2 in CW at https://amzn.to/3JgfX0p

Get the TC20 V2 in NW at https://amzn.to/3oFSV9A

 

Packaging & Accessories

Standard Thrunite brown cardboard box here with the elastic band, I would call it functional minimalism. Inside is the entire kit with almost everything you need to maintain and use the light for years. You get the light itself, a 5000mAh 26650 Thrunite battery, nylon holster, USB-A to C charging cable, lanyard, a bag of extras including o’rings, button seal, USB port cover, and split ring, a manual and warranty card.

 

Construction & Design

The light is made from Aluminum and hard anodized black. Build quality is always good from Thrunite and this is no exception. The tail cap provides a flat surface that allows for tail standing and has a lanyard hole. The cap is removable and non-magnetic. Inside there is a stout spring on the tail end only.

The body tube has traded knurls for milled blocks in an almost frag pattern. The corners are well chamfered though so it’s not too aggressive. Square Threads on both ends are anodized, smooth, and nonreversible.

The head features the standard Thrunite electronic switch with a metal button on top, and a small battery indicator LED in the middle. Directly opposite the button is the USB-C charging port that’s covered via a silicone rubber flap. It’s decent fitting and does stay out of the way. The light has moderate milling at the top for heat dissipation and weight reduction. The bezel is flat. The lens is AR coated and the reflector has a moderate orange peel. Overall small but positive design changes from the original.


Retention

Retention options include the included nylon holster. It has elastic sides, plastic dring, and a fixed belt loop. It gets the job done but is just of average quality. The light also comes with a branded lanyard and split ring that can be attached at the tail if you wish.

 

Size & Weight

I measured the length at 118.1mm, the diameter of the body tube at 32.6mm, the diameter of the head at 42mm. The weight with the battery is 242.5g. The light is IP68 water rated.

 

LED & Beam

The TC20 V2 is running the Cree XHP70.2 LED that Thrunite says is capable of 4000 lumens. It’s available in Cool and Neutral white, and I have the cool white version here. On my Opple meter, I measured 5737 lumens, 66CRI. The tint didn’t have any green tinge to it and it seems to be a constant current driver. 

You would think this would be a pure floody light but it actually has a decent amount of throw to it at the hotspot that’s fairly tight.

Mode spacing here is less than ideal. I am very happy that it still has firefly at 0.5 lumens, but with 3 main modes to cover 0.5 to 1800 lumens, there are some pretty big jumps there between medium and high going from 350 to 1800. Another mode somewhere around 1000 lumens would be nice at least.

I will insert the output results I got from my lumen tube testing here. 

 

Heat & Runtime

The light is able to sustain it’s 3500+ lumens for 3:45 before stepping down to around 1600 lumens where it will run for 45 minutes, before stepping down to about 1400 lumens to finish out the remainder of it’s 1:45:00 runtime. Peak heat during this time was about 58C. Running on medium nets an impressive 11:15:00.

Where this light really shines in my opinion is the amount of time it can sustain well over 1000 lumens. This light maintains over 1400 lumens for over an hour. I frequently get asked what light can I buy that will stay over 1000 or 2000 lumens for an hour, well here is a good option for you if that’s what your looking for.

 

UI

UI here is Thrunite’s standard. Single press to turn on, long press once on to cycle up between the 3 main modes, double press to go to Turbo, triple press to go to strobe. It’s a very simple interface, and it’s easy to use which is nice but also limiting. A fast ramping interface would work pretty well here too given the limited number of modes and wide range of outputs it must cover. 

 

Recharging

The TC20 V2 has onboard USB-C charging that’s protected by a silicone rubber port cover. I charged the light charged the light from LVP to full at 4.15v in 3:48:00. The curve here wasn’t as clean as I am used to seeing but nothing that I was concerned about. You are able to use the light during charging but only in low and medium modes. It charges via USB-C to C or PD without an issue. While the included battery is officially rated at 5000mAh, I tested mine with my Vapcell S4 Plus at 5500mAh.  

 

Final Thoughts

The 26650 flashlight form factor seems to have kind of fallen out of popularity with the increasing availability of 21700 batteries having similar capacities, but I like the 26650 size in my hand personally from an ergonomic perspective.

One of the best features here in my opinion is probably how long this light can sustain 1500+ lumens before stepdown. That’s a feat that many high lumen output lights just can’t do due to heat and battery fatigue. This does that with ease. That said mode spacing here could be better to give you something between 1853 lumens and 320 which is the jump between high and medium.

This is going to be a good all-around use light, I think it would be a good option for something like camping or emergency prep as it’s good around, has quite a bit of life at higher lumen outputs and size isn’t as critical of a feature.

Posted on

Sofirn SP33 V3 Review (3500 Lumens, Multi battery compatible, $32 price tag)

Sofirn has made an upgrade to their SP33 light after taking feedback from the flashlight community and come out with the SP33 V3 edition. It can use a several sizes of batteries such as a 26650, 18650, and even 21700’s. It features a Cree XHP50.2 at 3V LED and produces 3500 lumens in a pretty compact light and a very budget friendly price. Thanks to Sofirn for sending this to me to check out.

Sofirn is offering 36% off the SP33 V3 that’s available from Amazon by using the coupon LiquidRetro combine that with the click off coupon to save a total of 36% brining this to $32.24 before tax. Get it at https://amzn.to/32M5SoH

 

Thanks to everyone who is already following me on Instagram, and on this channel’s Facebook page, It really does help the channel grow. 

 

Watch this review on YouTube:

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

 

Packaging & Accessories

 The SP33 has a bit of a more retail looking box then we have seen from them in the past. It’s a black and orange hanger box but it doesn’t have a photo of the light on it, just a night shot showing a very bright flashlight. Accessories that are included with the SP33 V3 Kit are The 5500mAh 26650 battery, 18650 battery adapter tube, USB-A to C charging cable, manual, and a lanyard with a couple extra o’rings. 

 

Construction

The SP33 V3 is made of 6061 aluminum and hard anodized in black. Machining is good for the price range, with no major concerns. Starting at the tail cap, it has a crown and one side has 2 holes for a lanyard attachment point. They are just a little to small to easily fit paracord in, but you might be able to if you are patient and creative. Knurling is straight and there are a few flats in place for style. This is different from the rest of the light but provide function. Inside there is a single short fairly stiff spring that provides compatibility with the many different battery types this light supports. Threads are ACME cut and were dry in my example.

The body tube is reversible and has a decently thick walls. There isn’t a place for a clip but that’s ok for a light of this diameter in my opinion. The knurling is standard diamond knurling and is done in four panels around the light and is of medium texture.

The head is a solid piece. In the center you have the flat plastic e-switch button with an LED in the middle used for power indication. Around the hexagon there are small areas milled in to help with cooling and give style. Opposite the button is the USB-C port for recharging. The silicon cover here is a bit large and does protrude slightly from the lights back, enough so it won’t sit flat on this port but in the hand this works fine and stays out of the way.

The V3 features a deeper stainless steel bezel with a few short but long crenelations. This has been lengthened on the V3 version. The lens looks to be uncoated mineral glass and is fairly thick. The reflector underneath is deep with an orange peel.

 

Size & Weight

I measured the length of the light at 126mm, maximum diameter at 37.5mm, minimum diameter at 32mm. Weight with the included battery is 229g. 

I don’t have a lot of other great 26650 lights that are similar sized to compare it to. What I do have is the Wowtac A4 V2 I reviewed recently. It’s similar in length and diameter but the head is much larger. I also have the Sofirn SP36 I reviewed last year, its similar in length but has more diameter due to it’s 3 18650 batteries. 

Retention

Not much to say on retention here, there isn’t a place for a clip on the light, and it doesn’t come with a holster. The tail cap does have a place for a lanyard to attach if you wish. The light does tail stand without an issue.

 

LED & Beam Shots

V3 of this light is using a Cree XHP50.2 LED at 3V instead of the 6V version of this led. Tint is listed at between 6000-6500k, so cool white. On lower powers I do notice a bit of green tint shift on my example but it’s minimal. On higher powers you do notice tint shift across the beam. I would categorize the light as an all purpose beam, It’s fairly wide and the hotspot is so broad it’s not a thrower, yet it goes a good distance as you can see in my night shots. Sofirn quotes a throw of 275 meters and I think that’s a good number that’s in the ballpark.

V3 is using a FET driver instead of boost driver meaning it’s drawing more current from the battery thus the higher turbo output that’s seen here. You are going to want to use a good high quality high drain flat top battery with this light for maximum performance. It can accept 26650’s of all types, 18650’s of all types with the included spacer, or unprotected flat top 21700 batteries. The light has PWM on all modes according to my scope and solar cell setup. That said it’s pretty fast and my eyes or camera don’t notice it. 

 

Output is listed as:

  • Turbo 3500 Lumens
  • High 1600 Lumens
  • Medium 450 Lumens 
  • Low 150 Lumens
  • Moon 1 Lumen

 

Heat and Runtime

The SP33 V3 features Advanced temperature regulation without timed step downs, instead output will decline with the drivers internals reach 55C. Brightness will increase again when temps decrease, and we can see this in the runtime graph, as it’s a very seesaw motion. On average you’re seeing maybe a 20% swing in relative output over the life of the battery after the initial turbo step down. I didn’t notice it unless I was really focused on it on a 25 minute walk with the light. Turbo did start stepping down due to heat at 1 min 45 seconds, taking a little over a minute to step down to 18% relative output to cool. From here you can see on the graph it went up and down in terms of output as the flashlight regulated its own heat.

Total runtime on the included 5500mAh battery was 3:24:00. FL1 was at 3:11:00 and the maximum temp I saw during my runtime on the exterior was 48C or 118F so definitely very warm. All temps were taken at my ambient room temp of about 25C.

 

User Interface

 This light has 2 UI modes, default mode (mode 1) is a stepped mode that works logically. It has moonlight, low, medium, and high modes with memory and Turbo without. A single click turns the light on from off, and holding the button down cycles through modes. Long press when off turns on Moonlight mode and double click goes to Turbo. Triple click to go to SOS/blinking modes.

The second UI mode is a ramping mode. To switch between the 2 modes when the light is on do a quick quad press. Ramping is like many other ramping modes with a flash on both the top and bottom end. For me while I like being able to set brightness exactly where I want it, I don’t love the speed of the ramp here, it’s a little on the slow side. 

There is an electronic lockout when the light is off just quad click quickly. You can also mechanically lock it out with a slight twist of the tail or body tube. This is useful for such a powerful light os you don’t burn a hole in a bag or coat. 

 

Recharging

The light isn’t picky on the size of batteries used in the light diameter or size wise. It can accept 26650’s of all types, 18650’s of all types with the included spacer, or unprotected flat top 21700 batteries. The later having the most slop in the tube due to not including an appropriately sized spacer. I used the supplied 5500mAh Sofirn 26650 battery for my charging tests. LVP came in on the light at 2.895V, so a little lower then I prefer but acceptable. The battery measured as fully charged at 4.15V. 

The light does use USB-C for recharging which is nice to see. However it requires a USB-A to C cable (Supplied) to charge, and isn’t compatible with a C-C cable. When charging the small LED in the center of the button blinks red, and goes blue when charged. From LVP to full the light took 3 hours, 30 minutes. Maximum charging rate was 1.7A. 

 

Pro’s

  • Great budget friendly price for a lot of light in a good overall package.
  •  Is available in a few different versions, and battery options.
  •  UI is more “beginner friendly” than Anduril firmware.

 

 

Con’s

  • Still not fully utilizing USB-C to C, requires a USB-A to USB-C cable to recharge.
  • Very active thermal controls, with a good amount of change in output. 
  • No Neutral White tint option.

 

Conclusion

The Sofirn SP33 V3 is a low cost light with a lot of Output. Sofirn lists the light as making 3500 lumens. It runs on 26650, 18650 and some 21700 batteries so it’s widely compatible with the 3 most popular battery sizes today. 

 

It has features not usually found in this price category like USB-C charging (not compatible with USB-C PD (C-C) charging), active thermal controls, and a stainless steel bezel. The active Thermal controls are pretty reactive but they are smooth and I don’t notice it with my eye as much as the graph shows. I wish it was more widely available in Neutral white, they list it as an available option on their AliExpress store but I don’t see these available from other retailers. 

 

For the money especially with the discount Sofirn has provided makes this a really great value for the complete kit. It fits well in my hand and produces a ton of light. I can easily recommend this as a great high output budget light to pick up.

Sofirn is offering 36% off the SP33 V3 that’s available from Amazon by using the coupon LiquidRetro combine that with the click off coupon to save a total of 36% brining this to $32.24 before tax. Get it at https://amzn.to/32M5SoH

 

Posted on

Wowtac A4 V2 Review (617 Meter Throw, 1895 Lumens, 26650 Battery)

Today I have a review of the Wowtac A4 V2 flashlight that’s utilizing a Cree XHP35 HI LED an included 26650 battery to produce a handheld thrower flashlight with nearly 1900 lumens. Thanks to Wowtac for sending this to me to review. 

 

WowTac is having a sale for Father’s day on all of their products. 20% off all lights via the WowTac Amazon store, and 30% off the A4 V2 with my discount code in the description only on June 15 through the 20th. So make sure you check that out to get a gift for a dad in your life or to treat yourself. 

 

Get 20% off for all WOWTAC flashlights using the code “2LiquidRetro” at https://amzn.to/3eaPX5W

Get 30% off for the A4 V2 Neutral White using the code “3LiquidRetro” at https://amzn.to/2UHRV6f

Get 30% off for the A4 V2 Cool White using the code “3LiquidRetro” at https://amzn.to/3hoFmXk

The sale runs from June 15 to June 20, 2020

 

Watch this review on YouTube:

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

 

Packaging

Packaging is a brown rigid box with a deep lid that fits all the way to the base. Similar to other Wowtac and Thrunite lights. The outside is minimal with just the light name and line drawing and then emitter option on the side. Inside the light is protected with foam. Accessories include the 5000mAh Thrunite branded button top 26650 battery, basic lanyard, spare orings, and  spare button cover. 

Construction

The light is made from aluminum and anodized black. I have no complaints with the machining. The tail is non magnetic, flat and allows for tail standing. The light comes into 3 pieces, the tail, body tube and head. The tail and body tube has square knurled that are reasonably shallow, they do a good job at adding grip without being too aggressive. 

The tail cap has 2 large beefy springs inside, not what you typically see but it does a fantastic job of making the battery not bounce or rattle. The body tube is non reversible (anodized on the head end, raw on the tail end). The head itself is fairly standard, the steps up the the lens are closer to 90 degrees then angular and gradual. The front bezel is smooth and I was able to twist it off by hand. The glass is anti reflective coated. The reflector is smooth and deep, with the LED having some space around it at the bottom. 

 

Size & Weight 

I measured overall length at 125mm, minimum diameter on the tube at 32mm and maximum diameter on the head at 48mm. Weight with the included battery is 235g

 

Competition

A couple of competitors came to mind with the A4 V2, the Thrunite Catapult V6 and the Astrolux FT03. The Astrolux is closest in terms of price, but it’s head is significantly larger. I wouldn’t think about trying to carry the FT03 on my belt with a holster but with the A4 V2 that’s not an issue. The Thrunite Catapult V6 is similar, but has a slightly larger head. 

 

Retention

There isn’t much to say here on retention. There is a small hole in the tail cap for a lanyard that is included with the light. For lights like this a holster can be a nice option but one isn’t included.

 

LED & Beam 

The LED in use on the Wowtac A4 V2 is the Cree XHP35 HI. A cool and neutral white model are both available, and in my example I have the Neutral white. Tint is on the warmer side of Neutral which I enjoy I would say between 4500k and 5000k. The beam with this LED and the smooth fairly deep reflector is a thrower. You get a small tight hot center and a large dim spill. At lower powers the spill is not very visible. 

Wowtac’s claimed ratings

Turbo – 1895 Lumens

High – 1058 Lumens 

Medium – 208 Lumens

Low – 28 Lumens

Firefly – 0.5 Lumens

Strobe – 1200 Lumens

 

Heat & Runtime

I ran an uncooled heat and runtime test with this light and agree with Wowtac’s claims. Turbo has stepped down at the 3 minute mark to the 50% relative output mark where it ran till the 24 minute mark. Here is ran at about 42% relative output for the bulk of the time about another 108 minutes before stepping down and low voltage protection kicking in on the light at 2.985V. The light gets warm around the mid section where the LED is and other electronics. Maximum heat I saw during Turbo was 57C (134F).

 

UI

The UI here is standard Wowtac/Thrunite. It’s simple with just the features you need and nothing more. It’s a simple electronic switch under a slightly raised dome button. Underneath is a 2 LED (Red & Blue) to indicate charge status. It comes on blue briefly when the light is turned on. 

 

Long press from off to get moonlight mode. A single press turns the light on in it’s lowest mode. When on if you long press it will advance up in modes. You have a low, medium and high. Double press to shortcut to turbo, and once in tubo double press again to go to strobe. 

 

Recharging

The A4 V2 has onboard charging via MicroUSB. The port is slightly offset from the directly behind the button, not typical but not bad either. The silicone cover doesn’t get in the way. Total charge time for the included 5000mAh battery was 2 hours and 53 minutes. Charging started quickly, at 1.8A and generally increased up until the 2 hour and 18 minute mark before slowing down as it ended. Maximum charge rate I saw was right at 2A. The battery measured 4.155V when charging stopped. There is a LED inside the switch that’s red when charging and blue when charged.

Conclusion

The Wowtac A4 V2 is a nice budget thrower, available in both neutral and cool white, so everyone can be happy. It’s less expensive then other similarly sized lights running a 26650 battery with performance that’s just as good. It doesn’t come with as many accessories but for the price I am ok with that. 

 

Don’t forget about the father’s day sale here either, as this would make a great gift. It’s an all inclusive package with the battery and onboard USB charging. It’s available from Amazon so it will arrive fast and has a great return policy. If your dad or someone else in your life hasn’t had a modern LED flashlight powered by lithium batteries they will be amazed at how much and how far the light goes in such a small package. Gone are the days that you need a flashlight the size of a baseball bat, here are the days a ton of power fits comfortably in your hand and only weighs 8.29oz.

 

This is a nice budget light with no budget features. I can recommend it. 

 

Get 20% off for all WOWTAC flashlights using the code “2LiquidRetro” at https://amzn.to/3eaPX5W

Get 30% off for the A4 V2 Neutral White using the code “3LiquidRetro” at https://amzn.to/2UHRV6f

Get 30% off for the A4 V2 Cool White using the code “3LiquidRetro” at https://amzn.to/3hoFmXk

The sale runs from June 15 to June 20, 2020

Posted on

Lumintop ODF30 (26650 Flood, XPH 70.2, 3500 Lumens)

It’s been a long time since I have tested a Lumintop Light. Today I have the Lumintop ODF30 to take a look at. It’s a palm sized flood light that runs off of a 26650 battery using a Cree XHP 70.2 LED for an impressive 3500 lumens in Turbo. Thanks to Banggood for sending this to me, let’s take a closer look.

Full Image Gallery: https://imgur.com/a/jcyMafN

YouTube Version of this Review: (How do you like my new background?)

Packaging
The Lumintop packaging is very nice. The ODF30 comes in a nicely refind brown box with some details on the rear, the accessories including extra orings, orange lanyard, and holster are in a small separate box. The light itself is in a custom fit foam insert with a piece of clear plastic covering the lense. A 26650 battery is not included.






Construction
This light is made from aluminum and is finished with a dry flat black anodizing. Starting at the tail cap, It is flat and non magnetic. The light does tail stand well. Grip on the tail cap and body is blocky. It’s large milled squares in what I would call medium grip. It’s a unique look that I have not seen many other lights. The light doesn’t have any anitroll features built in.The light does come into two pieces, as it’s glued to the head.


The button is a positive click, covered by a rubber button. The head itself has quite a bit of groves for heat dissipation around it. On top the light has a polished steel bezel that’s smooth. The lens is a clear fairly thick mineral glass that’s not anti reflective coated. There is the signature Lumintop Red Oring that’s visible too.The reflector itself is pretty deep and has a nice orange peel on it. The LED below is nicely centered with a large dome on it.


Threads are square cut and anodized. My orings were greased but the threads were not. There is only one spring in the light connected to the driver board. The tail cap has a proud brass contact. Batteries are installed with the positive side facing the front of the light. I was using a KeepPower Protected 26650 and it’s a bit too long and dented the positive end slightly.

Length, Width, Weights, IPX
Maximum Length lenght is 119.5mm, maximum diameter at the head is 42mm, minimum diameter is 29.32mm on the body. Weight with the KeepPower 4500mAh battery I was running is 236 Grams or 133 Grames without battery. The light is rated for IPX8.

LED + Temps + Runtime
This light uses a Cree XHP 70.2 LED in cool white. It has a large dome on the LED. The LED didn’t have a Cree Rainbow as other XHP 70’s I have had have. Edges on the beam shots were fairly well controlled and it’s mostly a flood beam.

Runtimes were impressive for the ODF30. Turbo is timed to 3 minutes during which time it heats up. High lasted quite a while at about 20 minutes. Output did sag a little (still above 90% relative output) but before it stepped down to middle output. Middle output was about 140 minutes at about 65% output. At the end instead of stepping down and running on low the light seems to do a flashing a few times and shutting off. When it shut off it was still pretty warm to the touch, borderline uncomfortable. I used a KeepPower 26650 battery with this light that was rated for 4500mah.
 (Forget the slight dip upfront I had a problem with my sphere)

I ran another test 30 minutes from Turbo and generated an output curve for that shows that 3 minutes more in depth. You get a drop off pretty quickly but then it slows down the output drops taking slow steps. After about 8 minutes the light is pretty stedy for the remaining 35 minutes. At the end here the light was hot. I measured it at 124F uncooled which is uncomfortable to hold onto. If I was holding this I would have turned it down well before it got this hot. Parasitic Drain was measured at 3.2uA

UI
Ui is overly simple on this light. Low, medium, high in that order. When in high, double click to go to turbo. Eco mode (Still too high for my taste) is accessed when the light is off by long pressing the button till the light comes on. To shut it off while on requires a long press (2 seconds). Tho light also has Strobe but it can only be accessed from Eco Mode by double clicking to reach strobe. I like that strobe isn’t a part of the main group but this is a little awkward.

Lockout mode is also available. When the light is off long press for 4 seconds and the light will flash to enter lockout. To unlock requires unscrewing the tail cap. That’s certainly a different way to unlock and it’s not my favorite. Unscrewing the tail cap to mechanically lock it out seems more intuitive to me.

The light has low voltage reminder by flashing the LED under the button. This is a little hard to see if you don’t notice it. It comes on under 3V.

Compared to the Thrunite TC20
Size wise this is pretty similar to my Thrunite TC20 I reviewed. Both are floods with similar beam patterns. The Thrunite is a bit more expensive but it includes a 26650 battery, has onboard charging and is available with a Neutral white LED. Size wise they are very similar, I would give a slight advantage in build feel to the Lumintop. For me the Thrunite wins by a hair due to the neutral white LED which I prefer. Brightness wise to the eyes they are very similar.

Conclusion
This is a nicely built handheld flood. I like the 26650 format. It fits nicely in the hand while providing a large amount of light for whatever task you need. This makes a great handheld hiking/camping light with it’s long runtime or around the house work light/emergency light too. It’s not something most people will EDC in a pocket due to its size but it would work on the included holster for this. The XHP 70.2 LED in this is largely free of artifacts and color abnormalities I have seen with other similar lights.

For me lack of onboard charging isn’t a big deal because I have a few chargers that can accomodate 26650 cells. I would prefer the light to be slightly longer and use springs on both ends so that it doesn’t dent a protected battery that’s are a little longer. I would also like to see polarity markings. None of these are deal breakers nor do they detract much from a nice light. I do like that the 26650 battery format is starting to gain wider use in more and more lights.

Thanks to Banggod for sending this light for me to review. They have offered me some coupons if if you are interested in this light be sure to check them out.

Get $13 off the Lumintop ODF30 with coupon code: b3131d at https://goo.gl/cN2WBH

Get $2 off the KeepPower 26650 battery with coupon code: 6e5463 at https://goo.gl/rsf2Wx

8% off universal coupon for flashlight @ Banggood using code? Forolinternas