Sofirn LT1s Lantern Review (21700, Tint Shifting, Red, USB-C)

Today I am looking at the Sofirn LT1s, where the s stands for Small or Short. If you have followed my reviews you know I really enjoyed the BLF/Sofirn LT1. While the LT1s takes some design cues and even a few parts from it’s larger brother, the two are really different lanterns on the inside. The LT1s runs on a single 21700 battery, offers red mode, tint shift in white, aimable beam, and a different UI. Thanks to Sofirn for sending this to me now let’s get to it.

 

Watch this review on YouTube: 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on TikTok: https://www.tiktok.com/@liquidretro1

Enjoy this review? Buy me a Coffee/Beer: https://www.buymeacoffee.com/Liquidretro

 

Pickup the Sofirn LT1S Lantern at https://bit.ly/LQLT1S and use code BJ5B11QN to save 15%. (Valid till 4/28/2022)

The LT1S is also available on Amazon https://amzn.to/3Nz5xL5  use code 20WQ2PHC to save 20%. (Valid till 4/28/2022)

Here is the case I featured in the review, it fits but isn’t a perfect fit. https://amzn.to/3LlK1aO

 

Packaging & Accessories

Not much to write about here, Sofrin like usually has very basic packaging. Inside the light is wrapped in bubble wrap to protect it during shipping. Accessories with the LT1s include a 5000mAh battery that’s preinstalled, 2X extra orings, USB-A to C charging cable and the manual. 

 

Construction & Design

The LT1s takes many design ques from the LT1 on the top half at least. Starting at the top you have the hanger which is identical. You then have the main textured button that has a satisfying click to it, your 4 amber power level indicator LED’s, and the USB-C charge point. It’s a little odd to see the charge port be on top for moisture reasons, but the LT1s did survive a trip in the shower with me without issue. 

Below this is the same style of diffuser as the LT1 a white diffused hard plastic. The LT1s are all on the top of the light facing down, and in the white modes you can turn off half to better steer the beam to the side where you want the light, I will talk more about this later on. 

At the bottom you have the large tailcap. It doesn’t have much in terms of grip on it and it could be challenging to use with gloves or when wet. Threads here are ACME cut and sufficient. The tail cap has a large beefy spring to make contact with the inner battery tube, completing the circuit on the inside of the light. The large spring also allows you to run the light on an 18650 without issue other then some side to side rattle if shaken, even though it’s not officially rated for it. The head side also has a smaller spring. 

There is very minimal branding on the light, Only the Sofrin logo, model number and battery direction indicator on the front, serial number on the back and your typical CE, ROHS, and Recycling marks on the bottom. 

 

Thanks to Reddit user /u/DerMaxPower for allowing me the use of his deconstruction photos. You can see there are only emitters mounted on the top facing down, the center battery tube is aluminum which helps with heat dissipation. It’s a simple design but very functions.

Overall it’s a solid feeling lantern. The aluminum on top and bottom feel much better then the cheaper feeling plastic the competition uses. I suspect it makes it a good amount more durable as well. 

 

Mounting

Your primary method of mounting this light will be the wire bail at the top. This folds in either direction and can be removed if you wish. The LT1s ditches the ¼ 20 threaded receiving holes that the LT1 had and the tailcap is not magnetic. 

 

I spent some time on Amazon looking for a speaker case that would fit the LT1S and ordered a few things. Here is a link to the best one I could find at the time. https://amzn.to/3LlK1aO It’s not a perfect fit and a little to narrow but it does zip and leaves a little room for a charging cable and small charger if you wish.

 

Size & Weight

I measured the length at 97mm at the maximum height. Diameter at the top was 68mm, diameter at the bottom was 59.5mm. Weight with the battery is 338.9g. The light is IPX8 water rated and I confirmed this by putting it in the shower with me one day. I didn’t completely submerge it though. Here are some comparison photos with the LT1 and Olight O’Lantern. 

 

Emitters and Beam

The LT1s uses a lot of LED’s, 40 in total to be exact. 18x 2700k in the CSP 1919 package, 18x 6500k in the CSP 1919 package, and 4x Lattice Power Red LED’s. Sofrin doens’t give an exact model, but there is speculation they might be Luxeon brand due to the high CRI. My unscientific Opple meter measured the warm tint as 2585 CCT with a 97Ra, and cool white as 5732 CCT with a 100 Ra. I think these numbers should be taken with a large grain of salt for the Ra value. They are clearly high CRI probably above 90 but I wouldn’t read any more into it. It’s interesting that the cool white number didn’t quite hit the 6500k claim. In moonlight mode I did notice some PWM visible to the eye but this largely goes away in higher outputs at least to my eye. However it can be detected via my Opple meter or scope. 

The LED’s are mounted on the top of the light and well diffused to create a nice light pattern. The light does have the feature of being able to shut off one side while in white mode, to direct the beam to a 180 field of view rather than the full 360. This works pretty well,  I think it’s probably more useful to maybe not shine in your eyes so much if you have it out on a patio table or in a tent etc. It’s a nice idea but only works in the white modes.

 

Official Outputs

 

Runtime & Heat

I did lots of runtime tests here with all the different modes, and a few extra with the light powered by an 18650, and by a 10k powerbank. I will try to let the graphs do most of the talking here.

 

Since the light is capable of 4 tints I ran some tests multiple times and did comparisons. Here is the runtime test for the maximum warm output with the 5000mAh battery, As you can see the light can sustain nearly 100 relative output for 25 minutes before stepping down, Total runtime ends up being 3:09:00, with max temps reaching 42C. I ran the same test comparing Warm, Cool, and Neutral Outputs, and results are similar. Cool white had the least runtime, but only by 10 minutes, then warm. The surprise was Neutral white, it had the longers runtime by about an hour. More LED’s but less bright I assume. It resulted in a more linear output and ran out to 4:03:00. 

I also tested the runtime of running one side of the emitters in the warm mode at full output vs both sides. As expected running half of the LED’s result in a more stable output initially and for longer. It resulted in a substantial increase in total output but over half of this was at about 5% relative output so very dim. 

The red runtime shows the light isn’t able to sustain it’s high output for nearly as long as it’s white output in it’s highest mode before step down but the decline is slow. It has about 2:30:00 of it’s main output but continued to run at 5% for a considerable amount of time for a total of 5:30:00. 

Since an 18650 battery fits and makes contact I threw in a 3000mAh VTC6 and it’s output shape was identical to the 5000mAh 21700  but just shorter Total runtime was 1:43:00 vs 3:06:00. 

The lantern will also run directly off USB power (Without a tail cap or battery too when plugged into USB), although in lesser output. I ran it off a 10k powerbank and it ran for 12:20:00 which is impressive.

  • LVP – 2.738v
  • Full – 4.102v
  • Drain measured at 150-198uA

 

UI

Unlike the original LT1 the LT1s is using a UI Sofirn developed instead of Andruil. This is kind of disappointing because Anduril works so well on the LT1 and the special blinking modes are great there. That said my guess is Sofrin wanted a simpler UI, especially for switching between LED colors. The Sofirn UI here works well in my experience and the list below should serve as a simple guide of what you can do.

 

From On

  • 4 clicks to switch between ramping or stepped mode
  • 3 clicks to go between red and white modes
  • 2 clicks (Double click) to operate as a directional light and move between either side or full on just repeat
  • Double click when in red mode to activate SOS
  • 1 click and hold to change the tint of the light
  • 1 Click hold to switch between modes or ramp to adjust brightness

 

From Off

  • Long press to turn on to moon light mode. 

 

There is no ramping in Red mode and when you shut the light off in red mode, memory won’t return you to red. 

 

Recharging

The lantern recharges via a USB-C port on the top thats well sealed with a silicone cover. It is USB-C PD compatible, and it works as a powerbank to charge your smartphone or other device. My Samsung Smartphone reports it as charging via “Fast Charge” when plugged in. I didn’t do much testing here other then to verify it works. Here is the charging graph of the included 5000mAh battery from LVP at 2.738V to full at 4.1V. This took just at 3 hours and 18 minutes. Max charging speed I saw during this was 1.8A. The manual says it charges up to  3A max charging speed but I didn’t see anything like this. It may possibly need to trigger QuickCharge but it doesn’t seem to use the normal USB-C protocol for this. 

The light will run while charging although this significantly slows down charging speed. I ran the light at max output and started charging via a 65W USB-C power source, and at the end of 4 hours it was showing only one LED solid so between 25-50% power. I let the light go for 24 hours and it never fully completed charging but got to between 75-100%.

 

Final Thoughts

Lanterns are one of those things you can probably do without if you have a good flashlight but once you have one you immediately notice the value of having a light designed with a specific task in mind. The LT1s is the smaller, more stable, easy to use version of the LT1. 

Reading over the comments at BLF on the LT1s there are a few that are a little unhappy about the similarities in design to the BLF LT1 that Sofirn produces. That said I think most have concluded that the two are different enough not to ruffle too many feathers, and I agree. 

 

I like the more simple UI here for the most part, it’s going to be better for most people who are not used to Anduril nor want to take the time to learn it. The addition of red here is great for those who want to preserve night vision but even in low, I would say it’s almost too bright and on high it’s really bright. I like the ability to shut off half the white emitters to steer the beam, it’s nice for keeping the light out of your eyes if it’s sitting on a table or something. I am using this lantern quite a bit in the shower even to have something a little more soothing, and with less blue light.  

This is an easy recommendation for me, the pro’s easily outweigh the small cons. Sofirn has provided a 15% discount which I will have in the description/comments below the video. I will also have a link to the case I found that almost fits but isn’t quite thick enough for my liking. 

 

Pickup the Sofirn LT1S Lantern at https://bit.ly/LQLT1S and use code BJ5B11QN to save 15%. (Valid till 4/28/2022)

The LT1S is also available on Amazon https://amzn.to/3Nz5xL5  use code 20WQ2PHC to save 20%. (Valid till 4/28/2022)

Here is the case I featured in the review, it fits but isn’t a perfect fit. https://amzn.to/3LlK1aO

Wuben F5 Lantern & Fill Light Review (500 Lumens, 3 Tints, USB-C)

Today I am taking a look at a new Lantern and video fill light from Wuben with the F5. It can produce 3 tints, at 3 different brightness levels each, up to 500 lumens. It has an internal 5200mAh battery that can power the light and also be used to charge your devices. Thanks to Wuben for sending this to me to review and take a look at. 

 

Watch this review on YouTube: 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Enjoy this review? Buy me a Coffee/Beer: https://www.buymeacoffee.com/Liquidretro

 

Pick up the Wuben F5 at https://bit.ly/3xwOYqY and get 10% off by using the code CD10F5LR at checkout.

 

Packaging & Accessories

The Wuben F5 packaging is a nice box with a photo of the light and it’s lumens and battery size at the front. On the back you get a few more stats about the light and the box seals.

Included accessories is a rubberized lanyard, USB-A to C charging cable, and a metal 2 way S binder. The manual is usable but could use some polish by a native English speaker. 

 

Construction

The F5 is made from plastic all around. The build quality feels solid, with the front diffuser feeling a little hollow. The front panel is domed and acts as a diffuser for the approximately 90 LED’s underneath. The sides and back panel are all one piece and available in a dark green or black color. 

Each side of the light has a feature, with the top having 4 LED power and locator LED’s. On the left hand side when looking straight on you have the port cover for the USB-C input, and USB-A output ports. Opposite that you have the 3 buttons to control the light, on/off, and up/down buttons. On the bottom you have a ¼ 20 brass grommet to connect into for mounting or for use on a camera. On the back you have a raised circle that features a fairly strong magnet inside that easily supports the lights weight to mount on metal surfaces. Around that is a hinged metal ring with a fairly stiff hinge. You can use this as a small kickstand to prop up the light or to put your finger through to hold the light in a more secure way. One corner is drilled to accept the included lanyard. 

 

Retention

As mentioned previously there is the included rubberized wrist strap that attaches at the corner of the light. On the back there is the magnetic ring that supports the weight of the light well in any position on a variety of ferris surfaces. There is also that metal ring and stiff hinge acting like a kickstand or finger hold. 

 

Size & Weight

I measured the size at 78.8mm by 84.6mm by 33.7mm. I measured weight at 206.5 grams without the lanyard. The light is IP64 rated. So it’s dustproof and rated for submersion upto 1 meter. The light does not float. 

 

LED & Beam

There is no mention of exact emitters that are in use here but I can tell you there are 3 tints in this lantern, 3000k, 4500k, and 5700k. I can’t say exactly what CRI is here but my guess is somewhere in the 70-80 CRI, so pretty standard. There are a total of 30 emitters the 3000k and 5700k tints, 60 in total. For the neutral white mode the light actually runs both emitters at the same time. The beam is very even and diffused thanks to the frosted lens/diffuser on the top of the light. 

Exact outputs here vary based on the tint being used but Low ranges from 7-10 lumens, Medium 120-140 lumens, high 430 to 500 lumens with step downs from 230 to 300. 

 

There is some PWM here, especially in the lower output modes. I can’t see it with my eye but I can with my scope. The images here are from the warmer 3000k mode.

 

Runtime & Heat

Runtimes on the F5 are quite good, I did my runtime tests with a full 5200mAh internal battery on each color mode, in the top brightness. All 3 exceeded Wubens runtime numbers with warm white being 11:25:00, Neutral white and cool white both at 10:09:00. 

All 3 tints sustained theirs for about 8 minutes before stepping down to about 65% relative output. Basically this is a great light for long sustained outputs, perfect for that lantern application. Heat was really not worth talking about here, the sides and back stayed at room temp and only the front diffuser slightly heated up to be just warm.

 

UI

To turn the light on or off it’s a quick press on the center on/off/mode button. Wuben mentions stepless dimming here, and I don’t want anyone to get confused, this light does have steps, it’s not a light with ramping. That said the changes between modes are a soft fade. You have a plus minus button to adjust brightness in 3 steps. To change tint’s once on it’s a quick double press. The order it goes is cool white, neutral white, warm white. 

 

The battery indicators on the side also have what Wuben calls a Breathing LIght, I would call this a locator function. The lights fade in and out slowly to help you locate light in the dark. Useful for if your camping or trying to find it in a bag. This can be turned on or off if you triple click the central button with the light off. There is a lockout mode as well if you press that center button 4 times. 

 

Recharging

The Wuben F5 has a 5200mAh lithium ion battery inside. It’s non user serviceable. On one side of the light it as a large port cover that’s covering the USB-C port for charging, and a USB-A port to use it as a powerbank. There are 4 LED’s on the side that give you charge status when charging  and discharging. These values are a little different depending on the mode so make sure you consult the manual for the exact. 

 

For charging the light does support USB-C to C which is great to see, and in my tests took 3:22:24 to charge to full. Max charge rate I saw was 1.7A. 

As a powerbank I ran a discharge test at 2A, 5V which is the maximum it can output and it did this for 1:31:00. Capacity after conversion was measured at 3039mAh. So not the most efficient circuit here. 

 

Pro’s

  • 3 Built in Tint options with every light
  • Long runtimes for a pretty compact package
  • Charges via USB-C to C
  • Can be used as a powerbank
  • Strong Magnet, ¼ 20 grommet, and finger ring retention options

 

Con’s

  • Non user serviceable battery
  • Only 180 degrees of light instead of 360.

 

Conclusion

Lanterns are not the most exciting light in your collection but possibly one of the most useful. The Wuben F5 is up there in my opinion with the BLF LT1 I looked at last year. It’s smaller and doesn’t output in 360 degrees like a true lantern does, but it has a host of other features that make it useful for both the enthusiast and general user. 

The ability to run all 3 tints at 3 brightness levels really is great, for me I will definitely leave it in warm or neutral tints. The light is nice and diffused too.

I feel like the size and weight here are right. As much as I love the BLF LTF, it’s big, and heavy, the Wuben F5 is a reasonable size here and has more output/battery life then lanterns from larger brands and for less overall cost. 

If you don’t have a lantern in your go bag, I would strongly recommend one. This would be a great addition to that tornado, hurricane, earthquake or general power outage situation since you can use it to provide 10 hours of light on high, or 20 hours on medium, and use it as a powerbank to keep your phone topped off. Safe to say I am a fan and I do recommend it.

BLF LT1 Lantern Review (Variable tint, 90 CRI, Insanely Long Runtimes)

Today I have a specialty light, with the BLF LT1 Lantern, designed by forum members at the Budget Light Forums (BLF) and manufactured by Sofirn. The BLF LT1 started off 3 years ago as an offshoot of another BLF light the Q8 and shares a similar design internally with several components. Forget the other battery powered lanterns you have seen in the past, this one puts them all to shame. This will probably end up being a longer review so sit back and enjoy, it’s not like any lantern you have seen before.

 

YouTube version of this Review: 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

 

Packaging & Accessories

The main focus of this project was the light itself and as a result the light has generic packaging to prevent damage during shipping, not to attract buyers in a retail type setting. It ships in a plain brown package. Inside you get the manual which features the UI diagram, and a few spare orings, spare button and a orange o’ring that I put on the top of the light. The manual is pretty comprehensive and well written including a UI diagram, the aspect ratio is kind of squished though so I have included a link to the PDF copy

My light came with 4x Sofirn 3000mAh 18650 preinstalled. Each battery had a sticker on the negative terminal to prevent the light coming on during shipping. They ended up leaving a little residue that I had to clean off, so make sure you remove that before using the light. 

Construction

The light is made of anodized aluminum. The bottom half is the battery carrier and very similar in overall design to the Q8. The rear tail cap is removable, the knurling is similar on the  LT1 but it doesn’t have the flats milled in. Internally the cells are isolated from each other. Button top batteries are recommended with this light. There are two ¼ 20 tripod mounds, one on the bottom and on on the ring in the middle of the light.

 

The head silicone button as the BLF Q8 which features the T from Throfire (the Q8’s original manufacture). It has Orange LED’s inside that are on all the time as a locator function which you can adjust the brightness of or turn it off via the firmware. The button goes red when charging, and green when charged too. Opposite the button is the USB-C port used for recharging, and it has a larger silicone cover that fits flush. 

 

 

The diffuser is a thick hard plastic with a smooth gloss surface finish. It’s a very stiff piece and feels very solid. It does a great job of diffusing light from both the top and bottom emitters. Above this there is a small grove for an oring that I have placed the larger orange oring for looks. At the top there is a large folding metal hanger that fits tightly. This allows for securely hanging the light from a branch, tent, or ceiling.

Size And Weight

This is a larger and heavier then most of the LED, battery powered lanterns on the market but the build quality here is far better then anything else and it’s far lighter then the old steel and liquid kerosene lanterns. Weight with the 4 included 3000mAh Sofirn 18650 batteries is 641g. I measured overall length at 176mm, maximum diameter on the head at 68mm, minimum diameter at the body at 50mm. 

 

LED’s & Beamshots

This light is using a total of 8 Samsung LH351D emitters, 4 in 2700k 90 CRI and 4 in 5000k 90 CRI. The result is a light capable in its stock form of 600 lumens, and variable tin anywhere between a warm 2700k and a very nice neutral 5000k all at an impressive 90 CRI. Light is evenly diffused out the sides via the emitters on the top and bottom. Not much light is thrown up, instead it’s thrown more to the sides, so I find myself turning the light some if I need to read with it or walk with it. 

On the inside of the head there are some additional solder points that can be bridged to use more of the 7135 chips to increase the peak brightness of each group of LED’s. This only works when you are using more of one group of LED then the other, and decreases runtime, and increases heat. If you want to do this I would encourage you to read the long threads over on BLF first. 

Runtime and Heat

For my runtime tests, I ran the light in it’s default warm tint of 2700k with 4 of Sofirns included (Optional) 3000mAh button top batteries at it’s maximum brightness in it’s out of box configuration. Runtime here is just super impressive with total running out to 9 hours and 50 minutes before falling below 1% relative output. While this is dim it’s still useful light. Even at 95% relative output the light can sustain itself for 6 hours before starting a significant decline. Remember too this is only with 4X 3000mAh batteries, you could upgrade to 3500mAh batteries and get another 2000mAh to extend the runtime further. The light does have temperature regulation built in and it’s configurable in the UI. The top gets warm to the touch but not hot. LVP kicked in at 2.912V and the cells were all evenly, so running a matched pair of batteries with this light would be a wise idea.

The light will also run with the head off and powered by a powerbank at full output. This could be helpful in an emergency situation or if your charging batteries externally and still need the light. It will also run while charging but at a reduced output. 

 

UI

The UI on the LT1 is a modified version of Toykeeper’s Andrul. It’s well designed with lots of features but you don’t need to know how all those optional features work it if you don’t want to.

 

By default the light comes in smooth ramping mode which I personally like, but a stepped mode is available as well. To turn it on you click the button. To adjust brightness just press and hold till you reach your desired brightness. The light will give a quick flash at the top and bottom to let you know it’s at its maximum. A quick double click gives you turbo too. 

 

To adjust the tint of the light a quick double click and hold will then start ramping the tint and just stop when you get to your desired tint. Fairly easily you can get the light into a mode where tint varies with output level too, so warmer at lower outputs and fully neutral at maximum output. You can turn this on or off by double clicking and holding a couple of times till the light flashes. It’s a neat mode that mimics an incandescent bulb. 

 

Lastly if you want the light to be even more basic, there is a muggle mode you can put it into to hand off to someone who just wants an on off light at reduced output for increased safety and a dead simple ease of use.

 

For the more advanced features (Blinkies, strobe, aux button settings etc) you are going to want to consult the manual diagram. I keep the little printed manual in the Speaker case I keep my light in for transport.

 

Recharging

The light charges via a built in USB-C port which is great to see! On batches 1 and 2 of the light you must use a USB-A to C cable, but in batch 3 which is shipping now USB-C to C cables are fully supported. It’s nice to see full compatibility with both standards available. 

In my charging testes, I used the 4 Sofirn 3000mAh batteries that started at 2.92V and charged them to full at 4.05V in 10 hours and 15 minutes with the highest observed speed being 1.5A. This is on the slow side, while safe an conservative, I would have liked to see more like 2A charging.

 

I did briefly test the light with my solar charger too, and it works fine as I would expect. Given the long run times your probably not going to get a full charge during most days but it would be a great way to top the light up in an emergency situation or out while camping or hiking.

Case

So while not included with the light I thought I would mention this light fits beautifully in a case designed for a JBL Flip 3 or 4 bluetooth speaker. I picked up a Xanad case and the light fits great in it, and there is even space for a spare Samsung 2A charger and cable I had laying around. For $10 this is a no brainier in my book, Here is a link if you want to pick one up too. 

Pro’s

  • Even beam (flood) with variable tint 
  • Super long runtimes.
  • Easy yet powerful UI
  • Solid robust construction

 

Con’s

  • Weight
  • Previous versions (1 & 2) were not able to charge via USB-C to C, but Version 3 (Shipping now) can.
  • A bit of a slow charge time

 

Conclusion

You might have never thought you needed a lanter, but I am telling you this is the real deal. I live in the midwest and May & June are traditionally the months where we see the most amount of tornadoes and sometimes power outages. While you probably have a flashlight or several like I do, a lantern like this is really better for area lighting. It’s also great for camping, I would have killed for this when I was a Boy Scout camping, for all types of night activities etc. 

 

The combination of high CRI and variable (Warm tint) makes this truly a dream to use, there is no cool white here to washout colors and blind you, instead only pleasing warm and neutral tints with high CRI to help show the beauty of the nature you’re in. It’s nice around the house too just for area lighting or to read by if you wanted too. In muggle mode kids would love it too.

 

Super long runtimes means it’s very power efficient for the light it produces, but with that built in recharging via USB-C means it can be charged via solar panels too, to charge during the day, and light up all your night activities and repeat. While my version 2 here doesn’t support C to C charging, version 3 that’s available now does. The only downsides is the weight, it’s not light weight, and depending on your tent or how you want to try and hang it, it could be a bit of a challenge. You can remove batteries if you want to reduce weight and runtime, and maybe we will see a 1 battery version in the future. Remember it has those ¼ 20 tripod mounts too.

 

If you can’t tell by now I am a fan of this light and recommend it without hesitation. It’s a pretty decent  value and blows the competition away. If you’re looking for a great father’s day gift for the man who likes to camp, hunt or fish this is a great choice. If you want to build out your storm prep kit for tornadoes, hurricanes or blizzards this is a great add in. 

 

If you stuck around to the end of this review I sincerely appreciate it. Views during COVID have not been what I was expecting so if you have friends who like to camp, please consider sharing this video and blog post with them as I think this light has a wide appeal to non flashaholics too. Thanks for watching and stay safe. 

 

Buy from Sofirn Direct (Group Buy) https://sofirnlight.com/?DIST=QkFO

Sofirn Amazon with batteries https://amzn.to/2S6Swx0

Sofirn Amazon without batteries https://amzn.to/2xasFgp

Sofirn AliExpress https://bit.ly/2Y7V8ys

Full Image Gallery https://imgur.com/a/IHJClHH