Vezerlezer ED10 Review (2200 Lumens, SST40, USB-C, New Brand)

Today I have the first light from a new company Vezerlezer with the ED10. No idea if I am pronouncing the company name correctly or not. This is a 18650 based light, with an SST40 LED, onboard USB-C charging and a side mounted switch. Thanks to Vezerlezer for sending it for me to check and providing a discount code for 30% off good till 2023. 

 

Watch this review on YouTube: 

Follow me on Instagram: https://www.instagram.com/liquidretro/ 

Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/ 

Follow me on TikTok: https://www.tiktok.com/@liquidretro1

Enjoy this review? Buy me a Coffee/Beer: https://www.buymeacoffee.com/Liquidretro

 

Pickup the Vezerlezer ED10 from Vezerlezer at https://bit.ly/VEZED10

Use code CTZK5A8E to save 30% off the ED10 until 2023

 

Packaging & Accessories

The ED10 packaging is a nice retail style box, with a black, green and gray color scheme and various flashlight stats through out. Accessories that come with the light include a branded lanyard, extra oring, pocket clip, USB-A to USB-C cable, and a 2600mAh battery. 

 

 

Construction & Design

The ED10 isn’t breaking any new ground in terms of design but it does what it does pretty well. I am only going to hit the highlights here. Machining and anodizing are what I would expect in this price range but the edges are lacking champers around the head. The tail cap is flat, allowing it to tail stand and is non magnetic. 

There are quite a few markings on the light, with the logo, URL, model and company name appearing no less than 4 times, and they seem to be masked before anodizing, if scratched a bit it reveals bare aluminum at least on the tail. 

The body has a nice spiral shallow knurl in it. It reminds me of the Klarus ST15R I tested a while back. It provides a minimal amount of grip though. The pocket clip mounts at the rear of the body tube and the tube is non reversible.

The light does come into 3 pieces, with springs on both the head and tail. The head has a large anti roll ring, the switch is a metal eswitch with a near silent operation and a RGB led indicator at the center. The head has a large bezel that is removable, Inside is a lightly orange pealed reflector. What’s kind of unique is the reflector threads into the head which isn’t super common. As a result of all of this, it should be an easily modified light. 

 

Retention

Retention options with the Vezelezer ED10 are the included lanyard which attaches best on the side of the tail cap, or on the pocket clip. Your other option is the pocket clip. It’s a fairly deep pocket clip but the way mine is bent near the body it catches going into your pocket a bit. I think I can probably fix this with some pliers if I wanted to. 

 

Size & Weight

I measured length at 4.4” or 112mm. Maximum diameter at 1.1” (28mm) at the switch area, and minimum diameter of 0.96” (24.5mm). Weight with the cell and clip was 4.59oz or 130.2g. The light is IP68 rated and drop rated to 1.5m. Here are a few comparison photos to similar lights. 

 

LED & Beam

The light is running an SST40 LED in cool white. My Opple meter measured the tint at 6076k, and a CRI of 67 when in high mode. The beam profile is what I would call normal, primarily a central focused beam with minimal spill with no strange artifacts. PWM is present on all modes, it’s very a rapid PWM and I have a few graphs that show this from my Opple meter on high and turbo. Parasitic draw was measured at 20uA which is ok.

Official Outputs

  • Turbo – 2200 Lumens
  • High – 1400 Lumens
  • Medium – 560 Lumens
  • Low – 128 Lumens
  • Eco – 30 Lumens
  • Moon – 1 Lumen

Heat & Runtime

For my Relative output Runtime graphs I ran the Vezerlezer ED10 with the included 2600mAh battery. Turbo lasted to 2:40 with peak heat coming about the 3 minute mark at 51C. You can see active thermal protection on the light working through out the runtime as it takes little steps up and down to keep the temps regulated just under 50C before eventually turning off as power runs out at 1:40:00.

In my relative output comparison graph where I am basically comparing the runtime curves to one another (not total output), Turbo and high look very similar with high being slightly longer in runtime like you would expect but not in medium mode. Medium mode 

UI

The ED10 has 2 UI modes, stepped or ramping. To switch between them with the light off hold the button for about 5 second till the light flashes then let go. In stepped the light has memory mode. From off if you turn on and keep pressing the light will step up all the way to turbo and it stops. You have to press the button again to then step down. Anywhere you stop on that ramp, the next button press will step down. This is logical but takes time to get used to.

 

In ramping mode it behaves just like you would expect, except it only ramps to high mode, and you have to double press to go to turbo. The ramping is quite fast, and seems to be on a curve instead of linear. With the moon to mediumish being quicker then medium to high or so, maybe that’s because it leaves out turbo? In any mode triple click to get strobe.

 

Recharging

The ED10 charges via USB-C under a silicone cap opposite the e-button. The silicone cap fits well and stays out of the way. While charging the button turns into a charge indicator, red when charging, green when charged. The 2600mAh battery ended up testing 2694mAh, so that’s good.

Unfortunately C to C charging does not work here, so stick to the included USB-A to C cable. The charge curve here looks fine, it’s quite flat during the constant current charging for 2:32:00 minutes, but not very fast peaking at right around 1A. LVP is around 2.94v and the light charges the battery to 4.16v.

 

Final Thoughts

Not knowing what to expect from a brand new company I would say they have a pretty solid offering here for a first attempt. The exterior design is a nice size, I like the body tube milling rather than just standard knruling but you do pay in a bit less grip, and the port cover fits well. The beam properties are solid too, nothing really negative to say other then my standard gripe of cool white. 

That said there is room for improvement. The tail cap is just begging for a magnet with how flat it is, the pocket clip has that edge that catches on pockets, and they have went a bit overboard with the branding in my opinion on the light. I wish the battery was a larger size for the money being spent, 2600mAh isn’t that much in 2022 and the light really should be capable of C to C charging.

 

There are those firmware flaws that I mentioned in the UI section that another reviewer had found, None of them are deal breakers for me but they should be fixed. Ramping here is maybe a touch too fast in my opinion but I would rather it be faster then too slow. 

 

So in all a decent first attempt from a new model. The UI is easy to use, and the beam is suited just fine for EDC or general use. If they offered LED tint’s I think they could be a serious competitor with brands like Sofirn and Wurkkos for quality budget offerings. With the discount code that Vezerlezer has provided I think that puts the ED10 about where it should be price wise but it’s original MSRP is a bit too high to be competitive.