Posts

Posted on

Thrunite TC20 Review (XHP70.2 NW, 26650)

Thrunite gets a lot of positive attention with their flashlight models. I previously didn’t have one to review until recently with the TC20. The TC20 is one of the more recent designs from Thrunite(link is external) and I am glad they were able to send it to me for review. This is a 26650 based light, in neutral white capable of producing 3800 lumens and is microUSB rechargeable at 2 amps. Let’s take a closer look at it.

Full Image Gallery for this Review: https://imgur.com/a/BXRHr(link is external)
Youtube Version of this Review:

Construction
The TC20 is made from aluminum that’s been semi gloss black hard anodized. Machining is good with no sharp edges and everything lines up like it should with any printing, and flats on the body. The tail is non magnetic and slightly recessed. There is a small milled out area to attach the included lanyard as well. The tail cap and about ? of the body tube have a diamond knurling pattern that’s more on the aggressive side without being too aggressive to damage pockets. The head is milled from what looks like a solid piece of aluminum. It has 5 flats milled into the ring around the power button which helps control roll.

The button itself has a positive feel to it and makes an audible click. I believe it’s a metal top, with an LED in the center to indicate battery power level and charge status while charging. The reflector is deep and and has a nice orange peel to it. The glass lens is anti reflective coated. The silver colored bezel is removable and is used to contain the lens and reflector. Threads are large and square cut and unanodized. The spring in the tail cap is a double spring design.

!{width:80%}https://i.imgur.com/LgymZtP.jpg!https://i.imgur.com/LgymZtP.jpg(link is external)

Size and Weight
Length of the TC20 was 118.4mm, Maximum diameter was 42mm, minimum diameter was 33.55mm and weight was 238.7 grams. Compared to my Olight R50, it’s length was 132.4mm, it’s maximum diameter was 42mm, the minimum diameter was 33mm and weight was 258.8 grams.

The TC20 is IPX8 water rated which is great for a microUSB rechargeable light. Parasitic Drain was measured at a low 2.0uA.

LED + Runtimes
This light uses Cree XHP70.2 in neutral white as its emitter. I have tested a couple of other lights with the XHP70.2 and found the color rainbow effect where the tint of the beam is to be uneven. It was most noticeable on the eddges of the beam. However on the Thrunite TC20 this was much less noticeable, at distance outside I didn’t notice it at all. The LED is nicely centered in the reflector as well.

Outputs are good for a neutral white XHP70.2. I don’t have a way to independently verify Thrunites claims but in reading other reviews they appear to be accurate. Turbo is rated at 3800 lumens, High at 1800 Lumens, Medium at 320 lumens, low at 38 lumens and firefly at .5 lumens. Interestingly strobe is rated at 2280 lumens. Throw is rated at an impressive 320 meters.

Runtimes were close to what I expected with this light. Turbo starts to decline pretty rapidly which was a little disappointing, but high held for about 7-8 minutes. At that point the light was producing about 55% of its output and it saw one more decline where it held steady at about 40% of it’s output for about 90 minutes. This is still a significant amount of output for an extended period of time. At the tail end it was a pretty fast decline to zero where the low voltage protection kicked in and stopped output. Turbo to flat runtime was about 110 minutes.

One thing that’s interesting is in the manual it says not to use turbo for more then 10 minutes to protect the light, battery and it’s components. The light does get warm to the touch but never so hot that it feels dangerous to hold or like it could be damaging the light.

Beam Pattern
The beam pattern is pretty even, there isn’t a significant hotspot but there is a small less noticeable one. The beam is primarily flood but has a good amount of throw to it as well. In my outdoor shots you will see how well it really lights up a large area that’s approximately 100 yards in length. It’s a really useful beam in my opinion for general use especially when your looking to light up a large area at one time. See the video for more.

Charging
The light has built in USB charging via microUSB opposite the main mode button in the head of the light. To cover the port there is a beefier rubber cover that can be rotated out of the way. It can charge at a rate up go 2A which helps with charging speed greatly with the high capacity 5000mAh Thrunite button top 26650 battery that is included with this light. The light also works in Firefly, Low, and Medium mode. Thrunite includes a high quality USB cable with the light as well which I recommend using. If you see charging take over 2.5 hours make sure you look at your power source is providing a reliable, clean 2+ Amps.

UI
UI on the TC20 is basic and pretty logical. I like how they have chosen to keep strobe out of the main group of 3 modes (Low, Medium, and High). Turbo is accessible from any mode with a double click. Getting to strobe is slightly more difficult than other lights. You have to first be in turbo by double clicking and then double click again to go to strobe. I like this as I rarely have a use for strobe.

Moonlight mode is only accessible when the light is off by pressing the button and holding until it turns on. This light does have memory mode for the main 3 modes and you can return to it by just clicking the button once quickly. There is no software lockout mode.

The light also has a power capacity indicator in the main button. At 100% power it is a steady blue, at 11-20% power it’s red, at between 1 and 10% power remaining it flashes red.

Packaging
Thrunites packaging is a nicely executed and minimalistic. The light comes in a brown sturdy box with a line drawing of the TC20 and minimal info. It was held together with a clear rubber band. Inside is the lightself protected via foam with the battery preinstalled but using a contact protecting plastic disk that needs removed prior to first use. Under the foam is the USB cable, lanyard, holster, spare orings, side switch cap, and manual.






Comparisons
Compared with my Olight R50 which also has MicroUSB charging, and a 26650 battery the Thrunite TC20 is a shorter more compact design. It’s head is a bit smaller in diameter too. Knurling on the Olight is different, less aggressive. I do like the Thrunites more aggressive feel in the hand. Both fit well in my medium sized hand. The Olight has a beam that has a hotter spot and is designed for a bit more throw. It’s spill is less intense and has a harder cut off. The Thrunite TC20 beam is more even and seems to cover a wider angle. It’s neutral white LED really help bring out the natural color of things which I really prefer. Both are good lights lights, but for me the Thrunite TC20 wins out due to it’s slightly brighter, neutral white LED, and standard battery.


Pro

  • Relatively fast 2A charging on the included non proprietary 5000mah 26650 button top battery.
  • Neutral White Tint – but it does have some Cree Rainbow
  • Simple UI & Good mode spacing with Firefly
  • Nice fit in the hand and more compact than other similar lights.
  • I like that they include an extra side switch cap in the packaging.

Con

  • Cree XHP70.2 has some noticeable color shift across the beam, this has been similar across all of the XHP70.2 lights that I have reviewed, this is less noticeable at a distance.
  • No software lockout mode, but mechanical lockout works.
  • The holster is pretty basic, but functional.

Conclusion
I like this form factor for a light, it’s a good general purpose size for non pocket EDC uses. It would make for a great camping light or day/night hiking due to it’s runtime and good mix of throw and flood. For me it fits in the hand well without being too big or to small. I really like that Thrunite offers neutral white tints on many of their lights. I quite like this size of light, how well it tail stands and how much light it produces for a good amount of time without getting too hot. Thrunite has a presale running right now where you can save 20% off the cost of the TC20 by buying from their store http://www.thrunite.com/thrunite-tc20-3800-lumen-flashlight/(link is external) (Non affiliate).

Posted on

IDST C4 Smart Charger Review 3A charge, Color IPS Display

Battery chargers might not seem like the most exciting thing to read a review on but trust me this one is different and has a lot of neat features to geek out on. ISDT is an established brand in the Hobby charger market. They have historically been focused more in the RC market but the C4 I have in front of me today is targeted to more common battery sizes such as AAA, AA, and 18650s. This is my first formal charger review, so let me know in the comments what you would like to see in future charger reviews. Thanks to Banggood for sending this to me to take a look at it, this review has not been influenced by the manufacture or seller.

Full Image Gallery: https://imgur.com/a/QpI7Z
Video Review of the ISDT C4:

Construction
The body of this charger is constructed with a high density gloss white plastic, with the inner carrier where the cells go being a black semi gloss finish. ISDT claims this is a fire resistant plastic, which is nice but one thing I obviously didn’t test. On the rear you have the fan exhaust, power in, USB port for charging a phone or powerbank, and a MicroUSB in for firmware updates. The bottom has slots for cooling air to enter the charger. The front has a nice fairly large color LCD display thats 2.4” IPS display with a wide viewing angle. Itself isn’t touch screen but the touch panel is to the right and contains up and down arrows and a select.




The C4 doesn’t use the standard spring loaded contacts instead the contacts are hard mounted and have a bit of flex to them. Compared with most other battery charges I have (Nitecore, Xtar, etc) it’s a much less flexible in the size of cells that it will accept. I will go as far as saying it’s very picky.

18650 that are any longer then 650mm just will not fit. So most protected batteries are a no go. Unprotected Flat tops, or unprotected button tops seem to fit. Here are a selection of cells I tested fit with.

Sony VTC6 Flat Tops – Fit
LG HG2 Flat Tops – Fit
Samsung 30Q Button Tops – Fit
Sanyo NCR18650B Protected – Too Long
*Nitecore NL1894 *- Too Long
Xtar Protected 10440 – Too Long

I didn’t have any trouble with the KeepPower 14500’s, Eneloop AA, Ikea Ladda AA, Duracell Rechargeable AA. Amazonbasics AAA, and Duracell Rechargeables AAA seem to fit.

Limited Capacity
While this charger takes a decent number of sizes of cells (with some popular exceptions) it doesn’t always take very many of them at one time due to how it’s laid out.

Input power is via an included AC Wall adapter. The one in my package has a 2 prong European design and an adapter was included in the shipping package. Having to use the adapter means it’s not the most secure connection with the wall wart hanging off the plug. The charger itself is capable of a 12V or 24V input from an automotive source too and displays incoming voltage in the top right corner of the screen.



Modes and UI
In all modes when the charger is doing its thing you get lots of metrics on the display. You get the mAh that has been put in or discharged from the cell, The time it’s taken, The current voltage, and requested charge rate, the resistance, and temperature. Each bay has its own temperature probe and I believe they are at the positive end of the termal. So it might take a little time for heat to radiate to the sensor if the battery does get hot. It also plots a graph in real time as battery are going through their cycle. This graph scales in real time as time increases.

The C4 is compatible with a wide variety of battery chemistries including NiMH, NiCd, NiZn, Eneloop, Li-Ion, LiHv, LiFePO4.

The main modes of this charger are …

Charge – This is the default mode and probably what you use the most. It automatically detects the chemistry of the cell and for most the default charge rate is 1A.

Discharge – Does exactly what the name describes, it discharges the cell in the slot at the rate you choose. 1A seems to be the default speed. Depending on the chemistry the charger will discharge down to 0.9V for NiMH, 1.2V for NiZn, 3.1V for Li-Ion, 3.3V for LiHv, 2.9V for LiFePo4, and 0.9V for eneloop.

Store – This mode charges the battery to the optimal voltage for it’s type of chemistry. This is particularly useful for Lithium batteries who are happiest if they are not going to be used for a while to be stored at between 50-80%. I tested it on an 18650 and it stopped charging at 3.70V. Depending on the chemistry of your lithium battery it could be 3.8V or 3.2V. Storage mode will automatically charge or discharge the cell to get it to the optimal voltage. It’s only available for the Lithium based batteries.

Cycle – Will charge and discharge a battery a given number of times at your given speed. This could be useful on older NiHM or NiCad batteries. Default cycle here is 3 times but the charger will allow you to do this up to 99 times.

Analyze – Analyze will charge the cell up to 100% at the rate you choose, then do a full discharge at that rate, and then charge the cell up to full once again. During it’s run it tells you time, cell resistance and capacity in mAh.


Activate – This is used to activate a cell where the voltage has fallen below specs or on protected lithium batteries to reset a protection circuit. It uses a small amount of current to “wake” the battery up prior to charging. Caution should be used if using this mode.

UI(Video is best for this) is pretty clear and easy to understand. To the right of the screen there is a touch panel with an up, down and select button. They are pretty self explanatory, the up and down allow you to scroll and when you are on an option you want to change you touch the gear selector and then use the arrow keys to make a choice and then the selector to confirm. By default the charge goes to charge mode, in auto detection at 1A when you insert a cell. It gives you 3 seconds (Configurable) to make changes before charging begins. If you want to change modes of a slot while in use the only way to do this is to remove and reinsert the cell. It has a audible alarm and a very large flashing error message if you put a cell in reverse polarity.

The C4 also has the ability to charge another device via USB while charging the batteries in the bay. What’s a little strange is that it seems to prioritize this USB and it will limit current to the batteries instead of limiting the current to the USB port, just something to be aware of. ISDT lists it as 2.1A at 5V for USB charging.

I have some Thorfire 14500’s that this charger doesn’t seem to like. I can’t tell if it’s a bad battery or something else. I know they are not a great battery but they are also not terrible either. My other chargers like the Xtar VC4 charge it without a problem. This charger however will stop charging these at around 75% and act like there isn’t anything in the bay. If it was a bad cell I would expect an error message of some type.

My charger analyzer setup that enables me to graph charging curves isn’t friendly with this charger. The charger is too smart for it and the graphs that I have gotten are not accurate to what the charger itself is doing. I have some new parts shipping from overseas so hopefully that helps a bit for future chargers.

Firmware Update Process
This charge has a microUSB port on the rear that’s used for updating it’s firmware. When my unit arrived I checked the ISDT website and found there was a firmware update available. I was able to download the firmware which came with a windows only flashing program. I had to use AC to power up my charger then plugged it into my PC via USB and then started the program. It was recognized and I clicked the Start flash button in the application. The charger rebooted into a bootloader mode, transferred the file and rebooted. I do wish the log notes were more detailed about what changes between each firmware version. I didn’t notice a tone of difference but there are still a few bugs in the firmware it seems.
https://i.imgur.com/oHTm9nm.jpg

One firmware bug I have encountered is sometimes when I have a battery charging already and I go to insert another one the screen almost goes 100% white, It’s like the user interface locks up. I can’t make it happen regularly but it seems to only happen on the 2nd or 3rd battery insert. I also get some odd percentages as it guesses how charged the battery is at first. This seems to stabilize after about 10 minutes. This was new and I only noticed it after the firmware update I did. Hopefully a future firmware update will fix these issues.

In the Box
The box is nicely constructed and rigid with foam in the bottom and lid. The charger itself was housed in a plastic try with the Euro AC power adapter underneath. I like that they included a glass screen protector like you would put on a smartphone for the screen. It’s should keep the screen free from scratches.






Pro’s

  • Ton’s of advanced features and options that are all pretty easy to get to on the IPS display with the side touch interface.
  • It’s fast with a maximum of 25W of charging power and 10W discharge power.
  • Easily Upgradeable Firmware on a PC.
  • Well built plastic construction that’s fire retardant.
  • Super obvious reverse polarity alarm
  • Comes with a plastic screen protector you can apply.

Con’s

  • Limited to what cells can be charged by it’s design. No protected cells as the design doesn’t allow for anything longer then the standard 650mm in length. This also holds true for protected 14500 and 10440’s.
  • Small fan is loud and seems to come on based on the power level your charging at not the ambient temp.
  • Shipped with a European power adapter and requires a plug adapter to work in other countries (Included).
  • No manual listed online yet.

Conclusion
This is an advanced charger that has just about every option one would want, but it would be hard for me to recommend this to the flashlight community as someone’s only charger to do it all, because of inability to accept protected cells (Especially protected 18650). Protected batteries are popular on flashlights because they give an extra layer of safety. However for some reason ISDT choose a design that was less flexible on battery length which really compromises the offering in my opinion. I have had a few querkey issues too, mainly with the UI. These should be fixable in future firmware updates.

There are good things about this charger despite that though. It’s easy to use, with a relatively large, easy to read color display. The UI is easy to navigate. It has a wide variety of modes to handle your basic and advanced battery charging like charging, discharge, storage and activation needs. I like that the more batteries you put in it, it doesn’t slow the others down. It also has the ability to charge fast or slow if you want. The charger gives you a lot of data if if your the type of person who likes that thing, and I am.

For charging AA size NiMH batteries this is really a nice charger. It has the ability to cycle, charge, discharge, and analyze cells at pretty quick rates. It can fit 4X AA sized cells at once but only 2x AAAs at once.

For me this is my new AA and AAA charger. I will use it with 14500’s and flat top 18560’s that fit. It won’t completely replace my XTar VC4 as a do all charger but it will supplement it. I really like it’s storage mode for batteries that fit and wish protected cells fit too.

My hope for the short term is that ISDT continues to bring out more firmware fixes for the software bugs that I have noticed. It would be awesome if they had a email list you could join to be notified of new firmware. In the long term I hope that ISDT revises their design for the C4 and comes out with a model that can charge a wider selection of cells including protected batteries, and popular shorter batteries such as 18350, 16340, etc. It would also be nice to see a future model be able to charge 4X 18650 or 2× 26650 at a time. Since this model would most likely be physically larger I would prefer a larger, lower RPM fan to make it a quieter charger.

Thanks again to Banggood(link is external) for sending this to me to take a look at. They did provide a coupon (coupon Code “C48100”) that takes 8% off the price if you are interested in picking this up.

Posted on

Acebeam UC15 Review (1000 Lumens)

Keychain style flashlights have been a popular item over the past several years. Today I have the Acebeam UC15 which is advertised as the brightest flashlight of this style currently available. It can produce up to 1000 lumens briefly out of it’s main emitter. This light also has a red and UV emitters as secondary modes too. Thanks to Acebeam for sending this to me to take a look at.

Full Image Gallery: https://imgur.com/a/R7d5C(link is external)
Youtube Version of This Review: (Subscribe today! I am trying to hit 10k subs)

Construction
This is a solidly built light. The body and tail cap are made of a fairly thick walled aluminum. With batteries it’s a little heavier than I expected weighing 52 Grams. Mine here is in silver, but it also comes in a dark blue, black, and pink colors. Size wise it’s large then the Nitecore TIP and has no onboard charging. It seems a bit almost overbuilt for a keychain light but hopefully that means it stands up to hard use. Inside the springs are quite stout and gold plated. That said in the hand it feels better built.



Installing the batteries is easy if you know what your doing and potentially disastrous if you don’t. The manual surprisingly doesn’t tell you how to install the batteries. Since this light includes a hex wrench I initially thought you needed to remove the two rear screws, however this is incorrect. Instead just unscrew the lanyard attachment on the rear of the light and the back cover comes off. Insert two batteries of like chemistry positive end first and then put back on the cover and screw the lanyard loop back on to attach.

This light has a pretty substantial clip. More so than any other light in this size class I have seen. It uses two small hex head screws (wrench included) to attach to the body. This clip is very stiff and sticks out from the body of the light further than most. I think this is intended more to be clipped on to a hat with a bill and it should attach here quite securely. Be Careful not to cross thread the hex screws. They are small and it’s easy to do. A nice trick I always like to do is to rotate the screw backwards until it falls into place then switch directions to tighten it down.

LED, Run-times, and Power Source

This light uses a Cree XP-L2 LED for it’s main white emitter. There was initially some confusion here but it seems that the website and package are all in agreement. This light also has a Cree XPE-R2 LED for the red emitter and a Nichia 267A for the UV emitter. Only the white emitter has a reflector which is quite large, smooth and reasonably deep for a small light as well as a anti reflective coated glass lens. The red and UV emitters are surface mount parts with glass lenses over them. The red emitter is quite strong, enough so I wish it had a low mode. UV is rather low output but that’s common.


This light has 2 power source options, 10440 lithium batteries or AAA alkaline or NiMH rechargeables. It can also run on only one battery. To reach the full 1000 lumen output you do need the lithium batteries. Acebeam lists that turbo mode as lasting for 1 minute 46 seconds so it’s timed, after that it drops to 200 lumens, then 10. On AAA cells the maximum is 250 lumens, 82, and 10. Run-times for the Red and UV modes are similar regardless of the battery at between 1.2 and 1.6 hours.

I ran my own run-times on main emitter in the brightest modes with both battery types. With the 10440 batteries you had the nearly 2 minutes of a falling turbo before a longer than anticipated about 70 minutes of flat output in the 200 lumen range. However after that was over the output stopped completely. With the NiHM batteries (AmazonBasics) I had the a little more 250 lumen of output that was nearly flat, and at the 55 minute mark it took a sharp decline and then dove a bit more before a straight fall to the bottom at the 63 minute mark.

UI
This light uses a single electronic button which has an LED indicator under it. The button takes a firm press and makes an audible click. Memory mode is present on all modes. If you single click the light returns to where you previously was, including strobe. From off if you long press you go to the white driver, in low mode by default. From off you can double click to go straight to turbo and triple click to enter strobe. In any mode if you hold the button it cycles through each mode. When in white, a fast double click will allow you to go up in to higher white modes.

Packaging
Packaging is very nice, It’s a full retail box with all your important info on the front and back. On the side it does have Nichia listed with a check box so maybe we will see a Nichia offered as a main driver. We can only hope however I don’t think this will be very likely. Inside the light sits in foam, and to the side you have the pocket clip, hex wrench, and below are the instruction. They are decently written but a bit sparse for my taste.




Summary
This is more than your average keychain flashlight. I have tested the Nitecore Tip CRI which I liked, and I have tested the Astrolux K1 which had the 3 LED modes like the Acebeam UC15. The UC15 feels better built then these others but at a weight penalty. It uses batteries that are more accessible but I to an enthusiast I don’t know if that’s a benefit as I think many would have access to other lights for more dedicated tasks like a headlamp. That said this is a nice options for an upgraded nicer keychain light or pocket carry. Red mode is quite bright and UV mode can come in handy here and there. If you are looking for a keychain type light that has lots of extra features or a lot of output in such a small package, definitely check out the Acebeam UC15.

Posted on

Klarus XT32 1000M Thrower Review

Today I have a new large thrower style flashlight from Klarus, the new XT32 kit. This is a big flashlight, it produces 1,200 lumens and can throw over 1000M according to Klarus. Thanks to FlashlightZ.com(link is external) for sending this light out to me.

Full Photo Album: https://imgur.com/a/Q6j1h(link is external)
Video Review:

Construction
This light is made from aluminum alloy. It’s nicely machined with no machining marks. All edges have been broken by nice chamfers in most cases. Anodizing is smooth and semi gloss. Starting at the tail cap you have two mechanical buttons. One is a on and off which can be used for momentary and the other is a blad switch. There are recesses vut for both of these buttons creating very little area to allow such a tall light to tail stand. There is a hole for the included lanyard to mount to the tail cap if you wish. The tail cap itself has little grip for turning it, no knurling just some small areas milled out. If it was wet this could be difficult to remove. Inside are double golden colored springs that provide a good amount of resistance.





Looking at the threads on the body they are ACME cut and bare aluminum. It almost looks like there is a secondary inner tube but I learned my lesson not to pull on these. Below that is the removeable cegar grip accessory. Unfortunately this is just a little too loose for my liking and it spins with the tail cap screwed all the way in. It also has a small hole for the included lanyard. Further down the body you have an area that looks like a pocket clip would attach to it if one was included. I suppose you could put a tight fitting lanyard of sometype here or a mount but one isn’t included. Below that is a smooth short bit of the body. I am guessing this is for Klaruses Rifle mount even though the light’s tube diameter is 23.40mm and the rifle mount is for lights with a tube diameter of 25.4mm. Working my way to the front of the light there is a nice crosshatch knurling with some linear milled out ares that add some style and slight additional grip. This knurled area has two large flats, one with the label of the model and the relevant required markings and the other area being blank. This is just slightly off center of the side mount button.

Working my way to the head of the light the diameter increases as does the radicalness of the heatsinks. The side button is surrounded by a gear looking silver ring. The button itself is black and flat with a small indicator LED in the center.This is the battery level indicator. The head itself is large, it has mild crenelations on top. The reflector is under a large piece of anti reflective coated glass. The reflector is smooth and highly polished and the LED is nicely centered inside.

This light lacks a tripod adapter which I really like on larger lights. It’s a secure point to connect a more substantial lanyard and I find attaching it to a tripod or small gorillapod to be useful.

Lengths and Weights
This is a pretty tall light, I measured it’s height at just over 24cm, the head at it’s thickest is 64mm and at it’s narrowest is 23.22mm. Total weight with the included batteries is 358g. The light is rated for IPX8 water and dust resistance.

LED & Runtime
Cree XP-L Hi V3 LED with a maximum of 1200 lumen. It’s in a cool white that in my opinion isn’t too cool. I don’t notice an extreme Cree rainbow but I am not sensitive to this. The beam pattern is typical of a long distance thrower like this. At distances of shorter than 1 foot there is a donut in the beam. At a bit longer distances there is a very bright and intense center with a large but minimal spill and hard edges. At long distances the beam does give off a bit of a blueish tint but you don’t notice that in the intended target. Outputs go from low at 20 lumens, to medium at 100, to high at 400, and turbo at 1200. Since this is a thrower the important number is candella which is 250,000 in Turbo.



 On the Left Olight M3XS-UT, On the Right the Klarus XT32

This light has the Klarus ITS or Intelligent Temperature Protection System, and my output and runtime graphs indicate this. What’s disappointing is the slow decline from 100% output pretty much instantly. Decline is slow and gradual but by 10 minutes it’s at about 95% output which is decent. At that 10 minute mark there is a saw tooth decline for the next 10 minutes as the light increases and decreases in brightness according to temperature finally stabilizing at about 70% output. The 55-110 minute range the active cooling and managing battery voltage is pretty active. I did notice this step down when I was filming my night shots on a cold night where it was about 14F out.

In my night shots the light performed as I thought it would. Very similar to my Olight M3XS-UT but with a beam I found to be more pleasing.

UI This light has two main modes. #1 being Tactical and #2 being Hunting. In tactical you have access to one touch strobe and one touch turbo, one touch Low, SOS and mode memory as well as lockout. In Hunting mode you have on etouch turbo, one touch low, no access to strobe on the tail switch, SOS, memory and lockout. The diagram does the job of explaining all the different modes and how to get to them. I won’t lie both are a bit complex. For me I liked hunting mode best because it had access to both turbo by using the round push button and low by using the bladed switch. You could bump up in modes with the blade switch if you held it down and then short clicked it. There is also the front switch which allows you to cycle through modes or double click for strobe.

Electronic lockout is available but only for the sie switch. You press and hold for 5 seconds to lock and to unlock you press any switch quickly 3 times. The LED located in the side switch is a power indicator for the first 5 seconds of power on and goes from Green to orange, to red and to flashing red. This only works when using 18650 batteries.

Charger & Batteries
Included in the kit are 2 Klarus 2600mah batteries that are button top protected cells. These appear to be the same that was in my ST10 I reviewed a few weeks ago. I have no complaints other then I wish the capacity would be larger. This light has a working voltage of 5V to 12.8V so CR123A will work but 4× 18350 will not work.

I charged the included Klarus branded 2600mah batteries with the included Klarus charger. The terminal voltage after a full charge was 4.14V on both cells and this is well within spec. Charging speed is listed at 0.5A or 1A. I tested with 2 18650’s that needed a full charge and was only able to get about 0.85A out of it during charging. This charger also acts as a powerbank with charger 18650’s. You can have an 18650 (or smaller batteries like a 14500) in either bay or together to act as the powerbank. The manual really doesn’t tell about the charger, it would be nice if it included it’s own manual. According to the outside it’s capable of 1A discharge and I got pretty close to that during testing.




Packaging and Accessories
This light comes in a nice and compact box given its size. It’s a magnetic closure heavy duty cardboard and unfolds nicely but off balance. Inside is the light protected in foam. The batteries were preinstalled but did have a plastic separator that needed removal prior to use. It also included extra orings, and a Klarus branded charger that doubles as a powerbank.To see how those preform see above. It also included a small lanyard which is a bit disappointing. What I don’t like is the thin plastic reinforced connection that is the part that actually attaches to the light. For a light of this size and weight I was wishing for something more substantial. If it had a place for a tripod mount this would be an easy fix but instead I think I will have to create something with paracord and a slipping knot. It includes a short belt adapter that fits the head. This works but I think would be a bit awkward to actually use for a longer amount of time like during a hike.





Klarus sells some additional accessories listed on their website such as a tape switch and rifle mount, and colored filters to fit over the front of the light to complete the hunting package.

Comparisons
The Klarus XT32 is very comparable to the Olight M3XS-UT I reviewed several months ago. Both throw over 1000 meters with nice tight beams. The biggest difference between them is the LED being used and the controls. The Olight M3XS-UT uses a dedomed Cree XP-L that really creates a green cast to the light that is personally undesirable. The Klarus XT32 uses a Cree XP-L HI V3 LED that although it’s a bit too cool for my taste in tint it’s still better than the green cast of the Olight. I also like the tail switches and two different modes on the Klarus and the tail switch is better for tactical or hunting use. The front switch work fine for everyday use and I prefer the Olight shortcuts.
On the Left Olight M3XS-UT, On the Right the Klarus XT32


Pro’s

  • Seems to throw as well as my other 1000m thrower but with a better tint.
  • No ugly tint shifts or oddities in the beam pattern.
  • I like the two button tail cap button configuration and that Hunting mode removes strobe from the tail.
  • I like how you can lock the front button while still having access to the rear.
  • Well built and durable. The dual springs should let it hold up if mounted on a rifle.
  • It’s nice the built in kit contains a charger that has extra power bank features from both cells but it doesn’t have a wall outlet. It requires a MicroUSB input.

Con’s

  • No tripod adapter Sad
  • I wish the tactical ring on end of the light had a tighter fit so it wouldn’t rattle or spin.
  • Slower charger when charging 2 batteries at a time.
  • I wish it had larger capacity batteries. 2600mah in 2018 for a higher end models doesn’t cut it in my opinion.
  • Klarus again rated it’s lights using larger 3500mah batteries then what it shipped the light with smaller 2600mah cells.

I like this thrower, as mentioned the tint is a nice change over what I had on my Olight. Performance and throw works very similar to the Olight and I have no doubt it will reach that 1000m claim. I like the dual tail buttons and how they are used in the Hunting UI. I wish it was drilled and tapped to take advantage of a tripod adapter. Since hunting is one of the main uses for this light I would prefer they would have included the tape switch over the charger. That said the included charger although a little slower then speced works well and the dual USB powerbank feature is nice. If you are looking for a new hunting light to really cover long distances and the weight is ok with you this is definitely a light you should look at and consider. I will have a link in the description box below on where you can pick up this light on Flashlightz.com

Posted on

Olight M2T Warrior (1200 Lumens, 18650,18350,XHP35 HD CW)

The Olight M2T is a brand new tactical model introduced in late January 2018 at Shotshow 2018. It shares many things with it’s more expensive brother the Olight M2R. I reviewed it a few months ago and if you have not watched or read that review I recommend doing so. Thanks to Olight for sending the M2T to me to look at.

Full Image Gallery for this review: https://imgur.com/a/LaFOs
Video version of this review:

The Olight M2T shares a lot in common with the M2R. During this review I am going to compare the two alot. The easiest way for me to summarize this is to use some car analogies. Hypothetically let’s say the following. The M2T and M2R are the same model at their heart. The M2R is the fully loaded model, it has all the optional features, extras, and costs the most. The M2T is a mid range trim level model. Its performance is very similar but it has a few differences to reduce costs, such as the removal of the recharging system, and different tail switch, only one choice in emitter, etc. This is going to be a longer review, so grab your popcorn and let’s get at it.

Construction
Olight has excellent fit and finish for production lights in my opinion and this one is no different. Apart from the new tail cap on the M2T, the light is very similar in aesthetics and build quality to the M2R. The anodizing is a smooth high quality gloss black Starting at the top you have a signature blue Olight bezel with some mild crenelation in it. Below that you have the aluminum head and body. There are tier drop cuts in the head for heat dissipation and design. It has a nice hex edges to help it keep from rolling away on a flat surface. It’s a slightly different style then the M2R has, with fewer cuts. It does still have a completely milled flat edge opposite the button to serve as a locator. On the front side you have an electronic switch surrounded by a nice blue bezel with an LED in the center that is used for Low battery notification, lockout notification. Below that you have large square cut grip panels on the body of the light giving added grip and something a little different from traditional knurling. You can attach the two way clip at either end of this main body tube for head up or down carry.

 M2T on Left



At the tail end you have a new version of the switch that’s in the M2R. On the M2T this tail switch loses its recharging and magnetic features as well as its ability to tail stand. It’s replaced with a proud black rubber boot that has a dot pattern on it for texture. It still has the half press for momentary turbo and full press for lock and is silent. To full lock it does take some definite pressure. This switch operates and programs the same as the M2R. More on that in a minute. The tail cap of the M2T will fit on the body of the M2R and operate normally but not the other way around. Labeling is kept to a minimum, with branding near the head is always done so it can be read from left to light not as you rotate the light. The branding is at 2 and 10 positions when looking head on. The CE mark is opposite the button.

This light is rated IPX8 for moisture and dust and rated for 1.5M drops. I measured it’s length is 130mm it’s with at its narrowest point is 24.5mm and 27mm at its widest point. Weight was measured with an 18650 battery at 146.2G.

Inside this light uses a dual tube design which allows for the use of the two electronic buttons and the non proprietary battery. Do not remove this inner tube, it’s held in with an O ring and is hard to impossible to put back in place. Threads on the tail are a nice stout square cut.

LED & Runtimes
The Olight M2T uses a Cree XHP35 HD LED in cool white, this is the only LED and tint offered at this time. While I prefer a neutral white this isn’t so cold in tint that I dislike it. I did notice a little tint shift in the outer edges, but I think that blue bezel of the light also might be a factor in that. Depending on your power source maximum output (depending on your mode) is 1200 lumens compared with the 1500 lumens on the M2R. My M2R is neutral white so it doesn’t reach that full 1500 lumens and to me the two lights look the same brightness and the biggest difference is the tint. The beam is pretty even in shape. It has a smaller hot center and the spill is bright. At a distance it’s more like a flood then thrower, however for it’s narrow size it goes a good distance. It’s a very useful beam I find out to 100 yards.


Runtimes
I ran my tests with an Olight HDC battery that had a 3500mah capacity and a maximum continuous discharge of 10A. The M2T only ships with 2 CR123A batteries in a spacer tube instead of the high drain non proprietary Olight 18650 battery that was in the M2R. This is disappointing to me as to receive the best performance and longest runtimes, an 18650 is required. The light is also compatible with Flat top batteries, I had no issues with a Sony VTC6. Runtimes were good and what Olight is advertising. The light still has a timed Tubro mode which is 3 minutes. It then runs on high for 127 minutes before stepping down and running on moonlight mode. The graph tells the story. This light will also run safely on 2× 18350 batteries. I confirmed this with Olight that 8.4V is safe for the driver and that the batteries physically fit. I was unable to get a full working voltage for the driver though.


UI
Like the M2R the M2T has a rear button that provides momentary and full lock operation as well as a button up front for the full range of modes with shortcuts. One of the complaints I had about the M2R was that in normal mode you were limited to Turbo1 and not the brightest turbo which was only available in Tactical mode. The M2T fixes that by only having one turbo mode which is how it should be. The rear momentary switch was also slightly reprogrammed for an improvement. Now you have momentary on with a soft press, release and it will turn off. A firm press on this button will lock the light on in turbo for 3 minutes before it timed step down kicks in. You also have access to momentary strobe if you press in and keep holding the light goes into strobe at it’s new 13 cycles per second rate. The button up front has a total of 5 modes from Moon to Turbo with shortcuts to Moon (From off Press and hold) to Turbo (Fast double click), or Strobe (Triple click from off). Press and hold to advance in modes and there is memory. Pretty standard for recent lights from Olight. It’s an interface I like. Lockout is available but personally I just unscrew the tail cap ever so slightly to achieve the same thing. I thought the mode spacing is pretty good on this light.

As a Tactical and EDC
This is designed with tactical use in mind and it certainly could be used for that but I think it makes a good EDC option too. The proud tail button is easy to turn on if it gets any pressure. Given that the light comes on in Turbo when this happens I don’t recommend taking any chances, and I use mechanical lockout with just a quarter turn of the tail cap. It also offers an electronic lockout if you want to use that. The new clip is the same that is on the M2R and I like this dual clip. It can go on either end of the light and can be used either way. It allows for ultra deep head down carry which is what I like. For tactical use the strobe mode has been adjusted to 13hz and is now more easily accessed if you want it but not accidentally by holding the tail button down in the locked position for about 1.5 seconds. You can also get to it by triple clicking the front button. The bezel isn’t aggressive which is the way I would prefer it personally as it makes a better EDC and is less threatening in most situations.

Packaging & Accessories
Packaging on the M2T is now a bit smaller and less intensive to the M2R. I suspect this is to reduce overall costs and also make it easier to open. It is still very high quality but is now a white box with a pull through design. Inside the light sits in a nice tray, underneath it is a read before first use card, manual, lanyard, and holster . The holster design is different on the M2T. It’s less premium holster then the M2R. Gone is the latching clip, and extra padding, and metal grommet drain holes. Instead a heavy duty weaved nylon, with a velcro flap is the main holster. It still has a plastic D Ring and nylon belt loop. This is a more standard quality holster you see from other brands.







Conclusion
The Olight M2T is a still nice but lower cost version of the M2R. While it doesn’t have all the features of the M2R like magnetic recharging, it does have a few improvements in my opinion like only one Turbo mode, the melding of Tactical mode into normal operation. The new tail switch in the M2T is good, it’s a bit too easy to activate in the pocket so lockout is necessary. I do wish Olight would have shipped the light with an 18650 battery even though it doesn’t come with built in recharging. I guess that’s against what they do with their R series but it’s how the light gets the best performance in both output and runtimes I think it’s sub-optimal shipping it with CR123 batteries instead.

So which one do you pick? If you want Neutral white, recharging or a magnetic tail cap the M2R is the clear choice. If those are not important features or you want to save a little money the M2T is a good choice then. I do recommend running the M2T with a higher drain 18650 battery so make sure you have one of those too. I think the M2T will make a good choice of rifle light as well. I plan to test this when I get a mount that works for the light. Until then I think this might be the light that goes in my go/Tornado bag along with a few spare 18650 batteries. Let me know how you would use you your M2T. You can pick up the M2T on OlightStore.com.