Gear Reviews, Tech & Photography
Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Get the PhotonPhreaks Flood Ring with HyperGlow at https://bit.ly/36YWVuf
Today I have Nitecore’s newest powerbank the Carbon Fiber NB10000. It’s made from Carbon Fiber, all around, features 10,000mAh capacity, along with USB-C and A, and is capable of 18W input and output. Thanks to NitecoreStore for sending this to me to check out and review.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Packaging & Accessories
Packaging here is quite nice it’s a box that looks like it’s made of carbon fiber and it’s a pull out tray that has the powerbank, included USB-A to C cable, and the paperwork inside.
Construction
This powerbank is made from a carbon fiber reinforced plastic case, this is a more expensive stronger material then you find in most power banks. It feels a lot like a high quality tool that’s using a glass reinforced plastic. As for the carbon fiber on the top and bottom, I have my doubts here on it’s authenticity. When I hold it up at a certain angle and press near the front I can get it to deflect easily, there is also no texture in the weave that I can feel. At best it’s a peel and ply carbon fiber, at worst it’s a printed and stuck on. Other then that it’s quite stiff and feels well built. On one side all the inputs and outputs are laser engraved and easily read.
At the front you have one USB-A port for output only, up to 18W, then you have a USB-C port that can be used for In or out at 18W each. Next to it you have the single button on the powerbank with 3 blue LED underneath for power indication.
Oh and it’s water rated at IPX5 which is rare for a powerbank. It means it can sustain a low pressure jet of water or splashes, so it’s perfect for adventuring. Even though it’s not officially rated for it, I did submerge it briefly and it survived.
Size and Weight
I measured it as 122mm long, 59mm wide, and 10.5mm thick. This is nice and thin and slides behind most modern smartphones in a pocket while charging which is convenient when traveling. At 151.2 Grams it’s pretty light too thanks to that use of carbon fiber.
When I compare it to my Aukey 10,000mAh powerbank the Aukey is wider, longer, and 43g heavier. The 10,000mAh Anker powerbank I have is shorter but significantly thicker, I suspect it’s using cylindrical cells (21700?) and is 41 grams heavier.
Performance
As mentioned the NB10000 has one USB-A port for output only, up to 18W, then you have a USB-C port that can be used for In or out at 18W each.
I did my charging tests with my 65W Aukey GaN chargers that I previously reviewed on this channel and had no issues. Total charge time was 3:13:00. Peak charge I saw was 8.9V at 2.0A, or right at 18W. My CT-2 Meter recorded a total of 43.44Wh went into the battery.
Official Specs are as follows
Input – USB-C: 5V @ 2.4A or 9V @ 2A
Output – USB-C: 5V @ 3A or 9V @ 2A or 12V @ 1.5A
USB-A: 5V @ 3A or 9V @ 2A or 12V @ 1.5A
I ran 3 discharge tests, 5V at 3A, 9V at 2A, and 12V at 1.5A each performed as expected with power being pretty stable.
At 5V at 3A, I measured total energy at 31.29Wh, and average voltage at 5.18V and a total discharge time of 2:01:05.
At 9V at 2A, I measured total energy at 29.16Wh, and average voltage at 9.14V and a total discharge time of 1:35:58.
At 12V at 1.5A, I measured total energy at 29.71Wh, and average voltage at 12.02V and a total discharge time of 1:38:58, with a bit of voltage step down the last 20 minutes.
The NB10000 also offers Passthrough Charging meaning you can connect it to your charger, via USB-C and then charge your phone or other device (Flashlight) via the USB-A port, and both will charge at once. It’s not the full 18W speed but for me both my phone and the powerbank were full in the morning, making this great for backpacking or travel.
I charged my good old Note 8 from 15% to 100% in 1:51:00 via USB-C with 2/3 lights lit on the powerbank. I charged my phone again from 50% to 100% and the powerbank was still showing ? full.
It’s nice that the powerbank has a low power mode that you can activate by pressing and holding the single button until a white LED comes on underneath. This is perfect for charging an increasing number of low power devices like wireless headphones, smart watches and other wearables.
Pro’s
Con’s
Conclusion
The NB10000 is a small, well built powerbank with a great size to performance ratio. It has the features I am looking for in a powerbank in 2020, like PD support, 9 and 12V, and a low power mode. It doesn’t hurt it’s made of carbon fiber too since I am a sucker for it. That said you pay for these more premium features and this isn’t a cheap powerbank.
That said it’s my new travel charger since it’s so easy to put in a pocket and charge on the go. It also fits nicely in my camera bag which is also a plus. The traditional powerbank brands better watch out because Nitecore has them in their sights.
Pick up The Nitecore NB10000 Carbon Fiber Powerbank at NitecoreStore at https://bit.ly/3lssOiO
Today I have the new Reylight Quad Emitter Dawn flashlight by Maratac. It’s a CountyComm exclusive light producing 3200 lumens out of 4 Cree XPL-HI LED’s in 5000k and can be powered from a 21700 or 18650 battery. It’s got this really nice dimpled style texture on the body all done in this grey type 3 anodized body. Let’s take a deep dive on this light and show what it’s capable of.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Don’t forget to subscribe to my Youtube channel too, I can see that on some of my popular videos up to 75% of you watching this are not subscribed, so make sure you click subscribe now and turn that bell icon on, so you get notified about new videos every week.
CountyComm is giving my viewers 10% off their order of this light by using the code “LiquidRetro” at checkout. Check it out here if you are interested https://bit.ly/2SqBcTo
Packaging and Accessories
The Reylight Maratac Quad Dawn packaging is very simple. It ships in an orange hard plastic case with foam inside, some extra orings, and a plastic spacer for running an 18650 if you want to. The case is nice to store the light in but great to put other stuff in too. CountyComm is shipping these with a Samsung 40T 21700 battery but no charger. No manual is included but it’s a pretty simple 4 mode interface so you don’t need one.
Construction
The light is made from 6061 aluminum and type 3 hard anodized in a gray matt finish. Starting at the tail switch, it’s a recessed textured rubber boot with a mechanical switch underneath. It has a satisfying feel and sound too it. The clip attaches at the edge of the light, using 2 purple anodized titanium screws and a titanium clip. I will talk more about the clip in the retention section. The only branding is opposite the clip, and it has the Maratac logo and the serial of the light. This minimal branding is great!
The body and tail are a one piece design. I really like the almost golf ball like dimpling on the body of the light. CC says this increases the gripping surface by upto 300% over standard knurling, I don’t know how they come up with this calculation but I just like the feel in my hand and different look to most other lights on the market, and it won’t tear up your pocket insides. The head grows in diameter and has 4 tear drop shapes milled into it the length of the head. It’s a design feature that is common on many other ReyLight designs, like the LAN, and Gemini.
At the front the bezel is raw aluminum to provide some contrast and when standing on the head it allows light to leak out letting you know if it’s on or not. The lens is sapphire, which is great for scratch resistance. Below that is the quad carillo style optic and LED’s. There is a green glow gasket underneath, it’s reasonably bright but definitely not turbo glow.
Size and Weight
I measured the light at an overall length of 121.78mm, a minimum diameter of 25.5mm on the body and a maximum diameter on the head at 28.2mm. Weight with my 21700 battery is 140.1g. With a 30Q and spacer the weight was 127.6g.
The light is narrow for a 21700 and quad emitter light. Here are a few comparisons to similar quads or 21700 lights.
Retention
For retention this light has the same pattern Reylight has used on the Dawn and Gemini flashlights. It’s a wide paddle clip that has the popular Steel Flame spacing for the screw holes, so you can upgrade to a skull clip if you like. The stock clip is 1.2mm Thick and quite stiff. It’s a bit of a challenge to get it to clip to my pants pockets. That said it’s very secure and isn’t going to go anywhere once clipped. I like how this light feels in my hand, it’s the perfect size for me and that dimpled texture gives a nice grip.
LED & Beam Shots
The Reylight Quad Dawn by Maratac is using Cree XPL-Hi LED’s in 5000k tint so it fits that classic neutral white tint, but to me it seems on the cool side of 5000k. My preferences in recent years has opted to the warmer emitters but this is nice too. The optic is all flood, and it’s pretty even with no real distortions, not something you see on all quads. The beam has a broad center with a slight corona, and the overall shape is slightly square at short ranges.
Quad Dawn Beam Shot
Reylight Krystal Beam Shot
The middle 2 modes exhibit some PWM, It’s not bad and my eye or camera can’t see it but my scope can. See the example below.
Heat and Runtime
The Reylight Quad Dawn by Maratac has quoted outputs of 2 lumens, 250 lumens, 1400 lumens and 3200 lumens. I did my runtime test with an Xtar High Drain (42A) 4200mAh 21700 battery because that’s what I had two of. I did a complete runtime in Turbo, which isn’t recommended because of the extreme heat, but it’s how I test all my lights in the brightest possible mode and see where they go from there. On this light it starts stepping down pretty soon after and a 0:2:25 it’s down to 50% relative output. From here it holds itself for an hour before stepping down again and ending at around the 1:15:00 mark. During this time the light gets super hot, a whopping 78.9C (174F). This is dangerously hot, for both the battery and your skin. Again this isn’t recommended, CountyComm recommends only using “turbo” for 90 seconds and when you do that the light steps down much less and remains a warm but reasonable temp of less then 60C. I tested High only mode and fell a little short of the 2 hour quoted runtime but my battery is also 800mAh short of what the light ships with so I expect it to hit that without issue.
UI
The UI here is super simple, it’s a 4 mode flashlight, with moonlight, low, high and turbo. Mode spacing varies quite a bit, between 2, 250, 1400, and 3200 lumens. The mechanical button can accept half presses while on to advance the modes and then a full press to lock in on. There are no flashing modes on this light, which I am cool with. The light doesn’t have memory mode.
Pro’s
Con’s
Conclusion
The full name of the light (Reylight Quad Emitter Dawn Custom Maratac LED Flashlight + Glow Afterburner) is lunacy, but the quality of the light makes up for it. For a 21700 sized light it was smaller than I thought it would be. The slimness of the tube really helps.
It’s not something I will carry often in my front pockets for EDC for office tasks but you could carry it pretty easily in a larger pocket or back pocket if you wanted. It’s not too big in a front pocket either if you wanted. For me it fits great in the hand and that is only made better with the dimples for grip. It’s a great walking the dog type of light, high at 1400 lumens and the floody beam is more then you need, and with 2+ hours of runtime it is plenty for most people. One more mode between low at 250 lumens and high at 1400 lumens would make it a little more useful I think.
That said on Turbo for continuous use this light is dangerously hot, 78.9C (174F) is burn you hot, that said you I only saw this at the 31 minute mark and I don’t think you will see it in the real world because a sane person would shut the light off or turn it way down as you wouldn’t be able to hold it. I don’t recommend running your light in turbo for so long because it’s not good for the battery either.
Overall this is a nice light at a fair price. I enjoy it and am glad I have one. It’s easy to recommend and is a nice size too. Remember these are limited to only 500 lights and are only being sold through CountyComm, so check the description below for a link to their website to pick one up if your interested.
CountyComm is giving my viewers 10% off their order of this light by using the code “LiquidRetro” at checkout. Check it out here if you are interested https://bit.ly/2SqBcTo
The Jetbeam TH20 Guardian is an updated version of the previous popular TH20 Tactical flashlight. It’s rated for 3980 lumens from a Cree XHP 70.2 LED and a 21700 battery. It features onboard USB-C charging and has a powerbank function. Thanks to Jetbeam for sending it to me to review.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Packaging and Accessories
Packaging is standard Jetbeam hanging design with a nice photo of the light on the front and stats on the back. Inside accessories include the light, a 5100mAh 21700 battery, a belt holster, wrist lanyard, the USB-C OTG cable for charging and using as a powerbank, and then some nice spare red orings. Paperwork includes the manual, warranty card and COA.
Construction
The TH20 is a solid well built light all around. Starting at the tail cap it has 2 large square ears that protect the button and paddles well, and allow for a place for the lanyard to fit. The light will tail stand but it’s not very stable when doing so. The knurled areas on the tail and body are on the smoother side but the milled areas on the light and heatsync give you an area to lock into.
Threads on the inside are anodized, square cut, beefy and really smooth. Other manufactures take note, this is how it’s done. The tail cap has dual stiff springs, but the head only has a brass post, a little surprising for a tactical light. No issues with vibration though.
The head section has a section that looks like heatsyncs, I think it’s more style though, The front bezel seems to be glued in place, I can’t get to move, It’s short but has large crenulations allowing light to spill out. The antireflective coated glass underneath is thick and well protected. Under that is the deep orange peel reflector and the large Cree XHP 70.2 LED.
Size & Weight
I measured the overall length at 161mm. Maximum diameter on the head was 40.21mm and minimum diameter on the body was 29.5mm. The weight I measured with the battery, was 267.3g. This is a large light, no ways around that. See the photo below for some photos of similar 21700 sized lights.
Retention
This isn’t an EDC light to put in your front pants pockets, instead you have a holster option that the light comes with. It comes with a nylon holster, with a button belt loop and no Dring. The material here is nice but the stitching is all single stitch and it it’s not a premium feel.
LED & Beamshots
This light is using a Cree XHP70.2 LED in cool white. No tint data is given but it’s definitely cool white and has the characteristics of a XHP70.2 LED. So that means it has some beam distortion in the center, of a corona donut and then tint shift across the beam. It’s more a flood but the beam isn’t even, so I would call it on the floodier side of a typical flashlight beam. Definitely not a thrower.
The light has 4 solid on modes and then strobe.
No ratings are given for strobe but I would guess it’s equivalent to high or turbo.
Runtime & Heat
I am skeptical of the claimed 3980 lumens, at least that it can sustain it for any time. In my runtime graph here I see about 20 second before the light has stepped down. At this point it can sustain this mode for about 10 minutes before stepping down again due to thermal constraints with the maximum temp it sustained was 40.5C. Total runtime ended up at 2:26:00 but instead of shutting off the light ran for several more hours at basically moonlight mode. I stopped the test at 5:35:00. LVP kicked in at 2.946V.
UI
UI here is quite simple. You have a large mechanical button on the tail end of the light covered in a large silicone switch, it’s quite stiff, you won’t accidently press it, but it is loud. Next to it on both sides are metal paddles. When the light is off, the paddles give instant access to the strobe/sos mode of the light in a momentary manor. When you press the main button on the light the paddles give you mode options give you mode selections, with memory. The easiest way to lock the light out is mechanically by just turning the tail cap slightly.
Recharging
The TH20 offers charging via USB-C, but doesn’t support C to C charging. It features USB-A to USB-C which seems to be all most flashlights offer. Recharging the included the 21700 5100mAh battery from LVP to full took a total of 5 hours even, with peak charging rate 1.87A. The curve is a little abnormal but no big concerns with a battery this size. My one complaint is the LED light that gives the charging status is very close to the port, and combined with the port cover it can be hard to see depending on the cable you’re using. Charging stopped at 4.149V.
The light can also be used as a powerbank. It comes with a USB-C to USB-A Female adapter cable that can be used to charge your phone or other device from the light. It can also charge a device like my phone with just a USB-C to C cable. I did a discharge at 2A, but when doing this it didn’t seem to step down gracefully like I would expect or it could be my equipment, not many lights do the powerbank feature.
Pro’s
Con’s
Conclusion
I don’t have a ton of use for a light like this in my daily uses. It’s large, heavy and turbo is too short to be useful for me on my example. I do think the tail design is pretty decent for direct access to strobe in a tactical situation but 3 simple light modes plus turbo for your solid modes. I wish turbo lasted longer then 20 seconds, it would be useful in tactical and non tactical situations.
I love the color of the anodizing here, it’s gray brown anodizing, nice to see especially on a tactical light. The light is also very well built from what I can tell. Solid, and the rear switch takes quite a bit of pressure to push. If you need a solid well built tactical light thats in that middle ground between a flood and thrower then this fits that need, but isn’t going to be your best general purpose light in my opinion.
Take a look at the TH20 Guardian 2020 at BatteryJunction https://www.batteryjunction.com/jetbeam-th20-guardian-v2.html
Today I have a newer charger from Vapcell, the S4 Plus. This is truly a fast charger as it can charge all 4 bays at a maximum of 3A for a total of 12A. Speed is selectable too. It charges lithium ion batteries including protected 21700 sized, as well as NiHM cells as has a few other features I will talk about further on in the review. Thanks to VapCell for sending this to me to take a look at and review.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Packaging & Accessories
This is the updated charger that came out earlier this year. The changes are that the display is always on, the battery capacity in mAH is showend when fully charged, the cutoff voltage for lithium ion batteries is now 50mA when charging at 250mA or 500mA (good for small cells), The testing capacity feature for NiHM charges the battery, discharges and then recharges instead of leaving it discharged.
The package is a nice bifold box with printing on the outside showing the charge, showing what size batteries it charges, chemistry etc. Inside the charger was wrapped in bubble wrap and a generic 12V power adapter was included with a US plug in my case and a 5.3mm barrel inside.
Construction and Specs
Design and construction here are pretty standard for a charger, it’s pretty utilitarian in design. Construction seems solid with no creeks or cracks when twisted. I measured the length at 172mm, width at 115mm and depth at 36mm. Max charger expand size was 76.2mm which is great this means your protected 21700 batteries should fit, and there are not a lot of chargers that can say this. The spring loaded bays are pretty smooth too. There is no fan in the charger but there are some vents, when charging at max speed it gets warm but nothing to be concerned about. The screen here is fairly large at 78mm x 32mm. It’s a dark blue LCD with backlit silver white numerals.
My findings/UI
The charger has 4 main modes Charging, Discharge, Capacity Test, and Repair.
I am going to focus on the charging function and talk briefly about the others. Charging has 2 modes manual and auto. In Auto mode the charger picks the most appropriate charging rate for the cells measured resistance. You can override this to a degree if you press and hold the current button for 5 seconds, although there is some margin of safety built in for smaller cells so you can’t pump them full of power too quickly. In manual mode you click the current button to increase the charging rate in 250mAh and 500mAh increments. In my tests the charger stopped charging a lithium ion battery at 4.185V and a NiHM at 1.495v. When fully charged the charger plays and audible tone.
To switch between charging bays hit the display button, same with the modes. The display shows the battery charger percentage, current voltage, internal resistance, amount of power that’s gone into the cell, time elapsed, temperature, and total power in watt hour.
Discharge allows the cells to discharge down to 3.0V Capacity test mode will charge the cell up to full, discharge, and recharge measuring the power going in and out each time to get a good measurement of the cells capacity. Repair is useful for batteries that have gone lower then what’s safe, it very slowly and carefully applies power to the cell to try and bring it back to life.
There is also a USB out port on the top of the charger that can be used as a powerbank to draw off the cells when inserted. This works when you insert a lithium ion battery in cell 1 and there isn’t AC power plugged in. What I wish is when AC Power was plugged in it did output the same 5V 1A of power so you could say plug in and charge your phone or a light that had built in or magnetic usb recharging.
Pro’s
Con’s
Conclusion
Overall this is a nice charger that does almost everything I want in a charger for flashlights and other electronic devices. It allows me to charge my NiHM and Lithium ion batteries and select the charge rate in 250mAh steps, up to 3A per bay. It has an automatic and manual mode too. It will charge all 4 bays at 3A if I am in a hurry and have batteries that support that. It can discharge batteries fully, it will run capacity tests to help me judge if a battery is healthy or needs replaced. It supports long cells too which is important for those protected 21700 sized batteries that are increasingly popular in the flashlight world.
The one thing I wish it had a storage mode, this is one thing I like to do on my lithium ion cells when I know I won’t be using them for a while, it drains the cells down to around 75-80% as that’s where they are the most stable for long periods of time.
I have no hesitation recommending the Vapcell S4 Plus V2 charger here. It’s fast if you want that, it’s slow if you want control, and it fits all the most common flashlight sized batteries in use today as well as the common household sizes too.
Pick up the Vapcell S4 Plus on AliExpress at https://www.aliexpress.com/i/4000249374391.html
Today I have Olights new thrower flashlight, the Warrior X Turbo. It’s capable of 1000 meters of throw on 1100 lumens and 250,000 candella. It has an Osram LED, and is compatible with the pressure switch from the Olight Odin. Thanks to Skyben on Amazon for sending this to me to look at and review.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Packaging & Accessories
I won’t go into much detail here but the Warrior X Turbo has great packaging, arguably Olight has the nicest packaging in the production flashlight world. The light comes currently as two colors, you have the black model that I have here and then Olight does offer a limited production gunmetal gray as well. As a base package the light comes with a 5000mAh proprietary 21700mAh battery. Fun side note I will link to a video another flashlight reviewer did of how they make these batteries. You also get the latest generation of the MCC charging system, a Tactical Grip Ring (TGR), pocket clip, anti roll ring, lanyard, and a nylon holster.
Construction
The Warrior X Turbo takes a lot of the design cues from the Olight M2R Pro, in the tail cap and body, adapting them to the larger thrower platform. Overall build quality is great for a production light. First the more aggressive tail button is here, which does allow the light to tail stand but it’s not the most stable when doing so. The tail is also compatible with the locking remote switch from the Olight Odin so if you have that it works here great. Inside the tail is a spring loaded contact internally.
Threads on the body are anodized, nicely greased and have a double oring system, to interface with the anti roll ring and the TGR. I will talk in detail about the clip in the retention section. The grip on the body is the same as what was on the M2R Pro, a more aggressive triangle, and has a few flats milled in for labeling.
The head is glued to the body and really grows in size to accommodate the large smooth deep reflector. I like the relief that’s milled in to give it some more style and save weight. The front bezel is beefy with large solid crenulations that allow light the light to stand on its head and for light to spill out. It’s not glued in place and can be removed with some force. This does effect the beam shape on the outer edges. The lens is large and anti reflective coated.
Size & Weight
I measured the length at 159mm, maximum diameter at the head was 58mm, minimum diameter on the body was 26.2mm. Weight with the battery, clip, standard anti roll ring came in at 296.1g. Here are a few pictures of the light with a few similarly sized lights you might know.
Retention & Grip
You have a couple of retention options for the Warrier X Turbo, it does come with a captured pocket clip, but it’s 38mm from the top of the light. That’s ok because with the size of the head here, your not going to be EDCing this in a pocket. The captured clip is nice, it won’t rotate because of an extra tab in the clip and on the light and anti roll ring.
The stock anti roll ring allows you to use the standard cigar style grip without problems, but that can be a little uncomfortable so Olight includes a Tactical Grip Ring (TGR) that’s a softer silicon like material that slips on in its place.
Other options include a lanyard that’s included, and the included holster thats purpose built for this light. It has a velcro belt loop and plastic D ring.
LED & Beamshots
Olight doesn’t say which LED is in this light officially, but they do list the tint at 6000-6700k, and by looking at it my guess is it’s one of the OSRAM models we have seen in other popular throwers. I wish they would list the LED they are using like almost every other manufacturer does. It’s a cool tint but not blue. The beam has a small but very intense hot spot, possibly one of the tightest I have had in recent times. There is a spill but it’s very minimal, only a few percent of the center, and there is some distortion on the edges from the shape of the outer bezel that’s noticeable at short range. I didn’t measure any PWM on this light on either mode.
Runtime & Heat
The ability on the Olight Warrior X Turbo to sustain it’s turbo output was better then I expected. From start to full and stable step down was right at 9 minutes, and it stayed above 80% relative output for the first 6 minutes. At that point it was running at 50% relative output for 1:45:00. Total runtime was just shy of 3 hours. The good news is with such a tight beam even at the lower output throws pretty well. When the power level reaches 20% the light starts to vibrate every 5 minutes to let you know, when it’s below 10% it will vibrate every minute, and below 5% it will vibrate every 10 seconds. You can’t miss it especially if mounted on a firearm. Maximum heat I saw was 48C at the 9 minute mark. LVP was measured at 2.95V.
UI
The UI here is super easy, it’s a 2 mode light with momentary and full on tactual switch. Low is rated for 150 lumens and you can use it in momentary if you half press the button and hold, or a quick have press will lock it on. A full press gives you full power 1100 lumens before step down and a quick press will lock it on, or a full press and hold will work in momentary. It’s the same UI we have seen in other tactical Olights with a rear switch. This light also works with the pressure switch from the Olight Odin.
Recharging
I had a little bit of trouble recording the graph with the Warrier X Turbo with my equipment due to the spikes along the curve where the current drops very near zero which tricks the measuring tools, but overall charge time here was 5:30:00, and the maximum charge rate I saw was 1.92A. I measured the full battery at 4.172V. No concerns with the charging but I will have to look for a firmware update for my equipment.
Pro’s
Con’s
Conclusion
The Warrior X Turbo is a nice more compact thrower from Olight. It has almost as much power as the much larger, more expensive Javalot Pro, but in a size thats easier to use, and carry on your person. While this is designed as a weapon light with the compatibility with the remote pressure switch and to beagle to be mounted on a weapon, it also works pretty well as a super easy main thrower. To me the long 6-9 minute runtime on Turbo is hard to beat in many other thrower style lights in this price category.
It’s an Olight so it has the usual caveats, like the proprietary battery, and the cooler tints. If you are less sensitive to those things I can recommend the Warrior X Turbo as a pretty sweet well built thrower.
Get the Warrior X Turbo in Black on Amazon at https://amzn.to/32ntwHs
Get it in Gunmetal Gray at https://amzn.to/3hpK7yz
See my full reviews of these two lights below.
Thrunite T2 https://youtu.be/5Apvie0OZRg
Olight Seeker 2 Pro https://youtu.be/O3x90cZEMhw
Pick up these two lights
Thrunite T2 Neutral White https://amzn.to/3jVEcUm
Cool White https://amzn.to/30gZeVE
Olight Seeker 2 Pro https://amzn.to/2JqRgRR
Jetbeam has a new version of the RRT01 Raptor out for 2020. If you remember back to last summer I reviewed the 2019 version of the light and loved it. The 2020 version adds an Optional Nichia emitter and changes how the rotary ring and UI work as well as being more flexible with different battery versions. Thanks to JetBeam for sending this to me to look at and review.
Watch this review on YouTube:
**Follow me on Instagram: https://www.instagram.com/liquidretro/
Join the Facebook Page: https://www.facebook.com/LiquidretroReviews/
Versions
There are now 3 versions of the Jetbeam RRT01 that all share the same name. There is the original from about 8+ years ago, the 2019 version and now the 2020 version. Each having their own differences in performance, batteries, and LED. I do wish JetBeam would have added a V1, V2, V3 or used a different name with the light so it was easier for the consumers to tell the difference. The easiest way to tell the difference between the 2019 and 2020 is to look at the tail. The 2019 has a place for 3 tritium vials, whereas the 2020 has a button on the tail cap.
Packaging & Accessories
The packaging of the RRT01 is very Jetbeam, it’s a blue and black retail hanging package with all the details you need on the outside and side panels. As far as accessories, it depends on the version you get. My kit has the optional 2x extensions tubes that allow you to use 18500 and 18650 batteries in the light. In addition to this it comes with a 1100mAh JetBeam branded 18350 battery with microUSB charging onboard, 3 extra orings, an allan key, 2 extra screws for the clip (Not torx), and replacement rubber boot for the rear switch in gray. You also get a lanyard, manual, and other paperwork.
Construction
The light is made from aluminum and anodized a warmer light gray with the control bezel being a silver. It’s nice to see a different anodizing color here. Machining is very good. Starting at the tail, there is a bezel around the center mechanical on/off button. When the button is in the off state the light doesn’t tail stand super well, but when the light is on the button has retracted enough that it tail stands great, so really a pretty thoughtful design as it helps you find it when you want to turn the light on.
The body section of the light has knurling around it with 2 flats with the minimal labeling on each side. The light then grows to match the size of the head and control ring. Threads are wide, square cut and non anodized. By default the light will fit 18350’s and CR123A batteries which are great sizes for EDC but if you want more runtime you can insert one of the extensions and use a 18500 if you have them or add both if you want to use a 18650. Just remember to use a protected battery as this light doesn’t have LVP. When the extension are in place it’s a little less elegant I think and heavy in the head.
The rotary control ring has some areas milled into it to give grip. It has a detent on both ends of the control area. From 0 to 100% is about 160 degrees of rotation. There is no detent in the control ring for the 2020 version of the light. The ring moves quite easily, I would like to just touch more resistance. The rotary really allows you to dial in the exact amount of light you want very quickly.
The head has an aluminum bezel that’s mostly built into the light and not proud. It is not glued but you will need a tool to get it loose. The glass lens is double anti reflective coated and it has a deep reflector with a light orange peal.
Size & Weight
I measured the length at 91mm in it’s shortest configuration. Each extension adds 15mm to the overall length of the light. Maximum diameter on the head of the light is 26mm, and minimum diameter at the head is 24.5mm. The extensions are slightly larger in diameter coming in at 26.46mm vs the 26mm of the head of the light.
Weight in it’s shortest configuration with the included battery and clip is 114.6g. With a 30Q and the 3x extensions came in at 153.9g.
Comparisons
The most obvious comparison with the RRTR01 2020 is the 2019 version and the lights look very similar. The largest difference is that the 2019 version is shorter without the tail switch. The lens’s are a little different too, the 2020 lights lens has a light orange peel and is deeper and the bezel is smooth. The diameter of the head is slightly longer too. The extension tubes fit either light. When you put the extensions on the light looks a little funny to me, it seems longer and the proportions are just off a little. For an 18650 light it’s a little on the long side when compared to the FW3A.
Retention
The RRT01 like it’s predecessors are using the “standard” steel flame pattern clip meaning most aftermarket clips on the flashlight market should fit here. THe stock clip is a little longer than many at 61mm. The screw holes are hex head instead the more common torx.
In the pocket it carries reasonably well. The slotted tail bezel that’s around the tail button sticks up a little more then I want but does protect the button well from accidental activation. It’s still deep enough I consider it deep carry. I found the short length to be about perfect in the pocket, it’s doable to carry with the extensions on and an 18650 but it’s center of gravity is more to the head.
LED & Beamshots
There are 2 LED’s offered in the RRT01 Raptor (2020), a Cree XP G3 offering 80 CRI, and a Nichia 219C at 90CRI. I have the latter and it’s a nice warm 4000k. For me this is a great combination of tint and high CRI. JetBeam claims both are rated for 950 lumens, and that would be higher then I would expect out of a Nicha 219C as they typically don’t put out quite as much light as the Cree XP G3, so I take that with a grain of salt. It’s enough light to do the job easily. The beam here is nice for EDC, it has some center spot, about 20% of the beam and then fades to a useful spill. The rotary is very smooth and makes this light infinitely variable sub lumen up to 950. See the video version of this review for my Nightshots.
Heat and Runtime
Runtime here is very linear, I started my test with the included 1100mAh 18350 battery on full power. Output here was very linear and seems to not be regulated super well. There really isn’t much of a stepdown and the light ran above the 40% relative output out until 28 minutes. At 34 minutes the light shut off when LVP on the battery kicked in at 2.94V. The runtime here surprised me a bit, it’s rather short but then again this light doesn’t have much of a step down. It does get warm and the highest temp I saw was 59C around the 17 min mark.
I then tested with a 3000mAh 18650 battery. You need to use a protected battery with this light, I didn’t do that my first test and the result was the light ran until the cell was dangerously low right at 1V. I was not happy about ruining a battery here, but the result was significantly longer runtime. FL1 was at about 95 minutes, total runtime was just at 1 hour and 40 minutes. You can see thermal regulation kick in at the top end a bit.
UI
UI here is pretty unique to most other flashlights but it works pretty well. The RRT01 2020 version adds an on off switch at the tail of the light and combines with the rotary function in the head to change the brightness of the light. Once on rotate the ring to the right to increase in brightness, increase to the left to decrease in brightness. It is truly infantly variable as fast or as slow as you want. On my light I can turn the ring about 1/12 of the way before the LED begins to turn on.
This light does have an infinitely variable SOS and strobe modes as well. When on just rotate to to the maximum brightness setting and then to the left slightly 3 times and you get SOS, do this 4 times to get strobe. You can then dial back the brightness if you want. To exit just turn the light off and it goes back to normal.
Recharging
The light includes a 1100mAh Jetbeam branded 18350 battery that has onboard microUSB that you plug into the side of the battery. It has a multicolor LED on top that goes red when charging and green when charged. LVP is built into the battery and it stopped at 2.94V. Charged it stopped at 4.16V. When I plugged it in to charge I did notice the top of the cell got pretty warm, about 110F but this quickly dissipated. My guess is it’s doing this at first to gradually limit current going into the battery at the start of a charge. Overall the battery took 92 minutes to charge, and the maximum charge rate I saw was around the 70 minute mark at 1A. It’s a little odd to see that high of charge rate at the end of the charge cycle.
Pro’s
Con’s
Conclusion
The JetBeam RRT01 is the 3rd irrieteration of the light that shares the same name, while confusing for customers it’s a light I am enjoying. I really like rotary interfaces, I think they should be done on more flashlights as it’s intuitive and easy to operate for people of any age. The addition here of the on/off button on the tail instead of detents in the rotary makes the light less likely to come on in a pocket or when not in use but I think detracts from the overall rotary aspect of the light That said it still works pretty well but just requires you to change grips when using the light to turn it on and adjust the output.
The inclusion on some version with the extensions is smart, allowing you to use more battery types, it’s kind of an after though on design but it works reasonably well, especially if you want the extra runtime of an 18650, just be sure to use a protected battery since the light itself doesn’t have LVP.
The optional Nichia 219C emitter here is great. One of the features I liked least about the 2019 version was it was cool white and it’s great Jetbeam listed to this user feedback myself and others had. Overall this is a fun edc light, it’s a little on the expensive side but one I can still recommend. Make sure to check my links in the description as I will list any coupons or sales I get where you might be able to get a discount.
Banggood has a 30% off coupon for the 2020 version of the Jetbeam RRT01 at https://ban.ggood.vip/V8ca by using code: BGRRLM